manualshive.com logo in svg

Perkins SEBU9068-03, Руководство по эксплуатации и обслуживанию, Страница: 84 / 124

Поделиться
Скачать
Perkins SEBU9068-03 Скачать руководство пользователя страница 84

Illustration 35

g02729648

2.

Loosen bolt (5) and loosen nut and bolt 6. Also,

loosen nut and bolt (1).

3.

Loosen nut (3) and turn screw (2) counter

clockwise. Turn the screw (2) in order to give
clearance to remove the belt (4).

4.

Remove belt (4) and visually check all pulleys that

the belt operates. Ensure that all pulleys are clean
and free from damage. Ensure that the pulleys
rotate freely. Replace any component that is
damaged.

Illustration 36

g02603591

(A) Belt configuration

5.

Install the new belt, use belt configuration (A).

Visually check that the belt is correctly aligned.

6.

Turn the screw (2) clockwise in order to tension the

belt. Ensure that the link adjuster (7) is at the
maximum extension, refer to illustration 36 .

7.

Tighten bolt (5), nut, and bolt (6) and tighten nut

and bolt (1). Tighten these nuts and bolts to
50 N·m (37 lb ft).

8.

Rotate bolt (2) counter clockwise two complete

revolutions and tighten nut (3) to 30 N·m (22 lb ft).

9.

Install the guard, refer to OEM for more

information.

i03559623

Battery

 

-

 

Replace

Batteries give off combustible gases which can
explode. A spark can cause the combustible
gases to ignite. This can result in severe personal
injury or death.

Ensure proper ventilation for batteries that are in
an enclosure. Follow the proper procedures in or-
der to help prevent electrical arcs and/or sparks
near batteries. Do not smoke when batteries are

serviced.

The battery cables or the batteries should not be
removed with the battery cover in place. The bat-
tery cover should be removed before any servic-
ing is attempted.

Removing the battery cables or the batteries with
the cover in place may cause a battery explosion
resulting in personal injury.

1.

Switch the engine to the OFF position. Remove all

electrical loads.

2.

Turn off any battery chargers. Disconnect any

battery chargers.

3.

Ensure that the battery disconnect switch is in the

OFF position.

4.

Disconnect the NEGATIVE

“

-

”

cable from the

NEGATIVE

“

-

”

battery terminal.

5.

Disconnect the POSITIVE

“

+

”

cable from the

POSITIVE

“

+

”

battery terminal.

84

SEBU9068-03

Maintenance Section
Battery - Replace

Содержание SEBU9068-03





























































































































Отзывы:

Нет отзывов