manualshive.com logo in svg

Perkins 904D-E28T, Руководство по эксплуатации и обслуживанию, Страница: 28 / 110

Поделиться
Скачать
Perkins 904D-E28T Скачать руководство пользователя страница 28

Loose or Off Engine Components

Illustration 21

g06481343

Typical example

(1) Primary fuel filter, combined with electric

fuel priming pump and Water-In-Fuel
(WIF) sensor

(2) If equipped, secondary fuel filter
(3) Electric control module
(4) Low-pressure fuel line

(5) Link harness
(6) Inlet temperature sensor
(7) Exhaust assembly

i08185938

Product

 

Description

 

904D-E28T

 

Industrial

 

Engine

The

 

Perkins

 

904D-E28T

 

industrial

 

engine

 

is

 

a

 

single

 

turbocharged

 

engine

 

with

 

an

 

engine

 

prefix

 

of

 

FE.

Note:

 

The

 

front

 

end

 

of

 

the

 

engine

 

is

 

opposite

 

the

 

flywheel

 

end

 

of

 

the

 

engine.

 

The

 

left

 

and

 

the

 

right

 

sides

 

of

 

the

 

engine

 

are

 

determined

 

from

 

the

 

flywheel

 

end.

 

The

 

number

 

1

 

cylinder

 

is

 

the

 

front

 

cylinder.

28

M0108133-04

Product Information Section
Product Description

Содержание 904D-E28T















































































































Отзывы:

Нет отзывов