Perkins 5006A-E23TA Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 100

Perkins 5006A-E23TA Скачать руководство пользователя страница 78

Illustration 74

g01238305

3.

Tighten the grub screws (2) to a torque of 90 N·m

(66 lb ft).

4.

Install the guards (not shown).

5.

Restore the electrical supply to the engine.

i08456754

Fuel

Injector

-

Inspect/Adjust

NOTICE

Only qualified service personnel should perform this
maintenance. Refer to the Service Manual or your au-
thorized Perkins distributor for the complete proce-
dure to inspect or adjust the fuel injectors.

Operation of Perkins engines with fuel injectors that
have not been inspected or adjusted can reduce en-
gine efficiency, and also reduce engine component
life.

Refer to Systems Operation, Testing and Adjusting,
“Electronic Unit Injector - Test” and “Electronic Unit
Injector - Adjust” for the correct procedures to inspect
and adjust the fuel injectors.

i07398052

Fuel

Injector

-

Replace

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire.

NOTICE

Do not allow dirt to enter the fuel system. Thoroughly
clean the area around a fuel system component that
will be disconnected. Fit a suitable cover over any
disconnected fuel system components.

NOTICE

If a fuel injector is suspected of operating outside of
normal parameters it should be removed by a quali-
fied technician. The suspect fuel injector should be
taken to an authorised agent for inspection.

Refer to the appropriate Disassembly and Assembly
manual for the removal and installation procedure.

i08238504

Fuel

System

-

Prime

If

air

enters

the

fuel

system,

the

air

must

be

purged

from

the

fuel

system

before

the

engine

can

be

started.

Air

can

enter

the

fuel

system

when

the

following

events

occur:

• The fuel day tank is empty or partially drained

• The low-pressure fuel lines are disconnected

• A leak exists in the low-pressure fuel system

• The fuel filter has been replaced

Use the following procedures to remove air from the
fuel system.

NOTICE

Do not crank the engine continuously for more than
30 seconds. Allow the starting motor to cool for two
minutes before cranking the engine again.

78

M0122761

Maintenance Section
Fuel Injector - Inspect/Adjust

«
...
76
77
78
79
80
...
»

Содержание 5006A-E23TA





































































































Отзывы:

Нет отзывов