Perkins 5006A-E23TA Скачать руководство пользователя страница 72

Страница: 72 / 100

Illustration 67

g06597046

Typical example

Illustration 68

g01165836

(Y)

“

Min

”

mark.

(X)

“

Max

”

mark.

Maintain the oil level between the

“

Min

”

mark (Y)

and the

“

Max

”

mark (X) on the engine oil level

gauge (2), refer to Illustration 68 . Do not fill the oil
pan above the

“

Max

”

mark (X).

If necessary, remove the oil filler cap (1) and add

oil. Clean the oil filler cap. Install the oil filler cap.

i08397579

Engine

Oil

Pump

Inspect

failed

engine

oil

pump

may

result

seizure

the

crankshaft.

failed

engine

oil

pump

may

result

contaminating

the

engine

lubricating

system.

Visually

inspect

the

oil

pump

for

leaks

damage.

abnormal

noise

observed

the

oil

pump

area

with

the

engine

running,

there

may

problem

with

the

engine

oil

pump.

Check

oil

pressure

using

Electronic

Service

Tool

(EST)

determine

the

oil

pump

failing.

For

information

consult

your

Perkins

distributor.

M0122761

Maintenance Section
Engine Oil Pump - Inspect

Содержание 5006A-E23TA




































































































Результаты поиска

Содержание 5006A-E23TA

Отзывы:

Perkins 5006A-E23TA, Руководство по эксплуатации и обслуживанию, Страница: 72 / 100

Результаты поиска

Содержание 5006A-E23TA

Отзывы: