manualshive.com logo in svg

Perkins 5006A-E23TA, Руководство по эксплуатации и обслуживанию, Страница: 71 / 100

Поделиться
Скачать
Perkins 5006A-E23TA Скачать руководство пользователя страница 71

3.

Install the new filter element. Align the clips (1).

Install the bowl (2).

Connect the power supply to the engine. Operate the
engine and check for leaks.

i02415257

Engine

 

Mounts

 

-

 

Inspect

 

Misalignment

 

of

 

the

 

engine

 

and

 

the

 

driven

 

equipment

 

will

 

cause

 

extensive

 

damage.

 

Excessive

 

vibration

 

can

 

lead

 

to

 

misalignment.

 

Excessive

 

vibration

 

of

 

the

 

engine

 

and

 

the

 

driven

 

equipment

 

can

 

be

 

caused

 

by

 

the

 

following

 

conditions:

• Improper mounting

• Loose bolts

• Deterioration of the isolators

Ensure that the mounting bolts are tightened to the
correct torque.

Ensure that the isolators are free of oil and

contamination. Inspect the isolators for deterioration.
Ensure that the bolts for the isolators are tightened to
the correct torque.

Replace any isolator that shows deterioration. For
more information, see the literature that is provided
by the OEM of the isolators.

i08238446

Engine

 

Oil

 

Level

 

-

 

Check

 

Hot oil and hot components can cause personal
injury. Do not allow hot oil or hot components to
contact the skin.

NOTICE

Perform this maintenance with the engine stopped.

Note:

After the engine has been switched OFF, wait

for 10 minutes to allow the engine oil to drain to the
oil pan. Then check the oil level.

NOTICE

Operating your engine when the oil level is above the

“

Max

”

mark could cause your crankshaft to dip into

the oil. The air bubbles created from the crankshaft

dipping into the oil reduces the oils lubricating char-
acteristics and could result in the loss of power.

M0122761

71

Maintenance Section

Engine Mounts - Inspect

Содержание 5006A-E23TA





































































































Отзывы:

Нет отзывов