Perkins 5006A-E23TA Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 100

Perkins 5006A-E23TA Скачать руководство пользователя страница 69

3.

Remove old element (2) and discard. Note the

orientation of the filter element for installation.

4.

Check the new filter element for damage before

installing new filter element into filter body (1).

5.

Ensure that end cover (4) is clean and free from

dirt before installing end cover (4). Then, secure
clips (3). The engine is equipped with 2 filter
elements, when performing maintenance both
filter elements must be changed.

6.

Connect the electrical power to the engine.

i02415251

Engine

Air

Cleaner

Service

Indicator

-

Inspect

Service

Indicator

Check

Check

the

service

indicators.

Replace

the

air

filter

elements

if

one

of

service

indicators

has

been

triggered.

Illustration 61

g01242320

When the air filter element is in a serviceable

condition, the center section of the service indicator

(1) is clear.

Illustration 62

g01242332

When the air filter element requires replacement, the
center section of the service indicator (1) is red.

Service Indicator Reset

Illustration 63

g01242328

Once the service indicator has been triggered and
when the air filter element has been replaced, the
service indicator must be reset. In order to reset the

service indicator (1), press the button (2).

If the service indicator does not reset easily, the
service indicator should be replaced.

Note:

The service indicator may need to be replaced

frequently in environments that are severely dusty.

i08399384

Engine

Crankcase

Breather

-

Clean

The

breather

has

no

filter

element

that

needs

to

be

replaced.

The

breather

will

only

require

cleaning.

M0122761

69

Maintenance Section

Engine Air Cleaner Service Indicator - Inspect

«
...
67
68
69
70
71
...
»

Содержание 5006A-E23TA





































































































Отзывы:

Нет отзывов