Perkins 4006-23 Скачать руководство пользователя страница 56

Страница: 56 / 88

Illustration 38

g06079895

Each belt must be checked.

Loosen nuts (4) on fan adjuster plate (5). Loosen

lock nut (3).

Turning bolt (2) counter-clockwise will adjust fan

pulley (6) and loosen the fan belts (7).

Turning bolt (2) clockwise will adjust fan pulley (6)

and tighten the fan belts (7).

When the fan belts (7) are at the required tension,

tighten nuts (4) to a torque of 85 N·m (62 lb ft).
Then, tighten nut (3) securely.

Install guards (1) and restore electrical power to

the engine.

Replace

Refer to “Disassembly and Assembly Manual”V-Belts
(Fan Drive V-Belts) - Remove and Install for more
information.

i06729752

Belts

Inspect/Adjust/Replace

(Alternator

Belt)

Inspection

Isolate the electrical supply to the engine.

Illustration 39

g06018436

Typical example

Loosen the bolts (1) and (3). Remove the guard (2)

from alternator (4). If necessary, loosen the bolts
(5) and(7) and remove lower guard (6).

Inspect the belt (10) for cracks. Inspect the belt for

contamination. If necessary, replace the belt.
Refer to “Replacement” for more information.

SEBU9077-01

Maintenance Section
Belts - Inspect/Adjust/Replace

Содержание 4006-23
























































































Результаты поиска

Содержание 4006-23

Отзывы:

Похожие инструкции для 4006-23

Бренды по названию

Популярные бренды

Perkins 4006-23, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 4006-23

Отзывы:

Похожие инструкции для 4006-23

Бренды по названию

Популярные бренды