Perkins 1706J-E93TA Скачать руководство пользователя страница 98

Страница: 98 / 130

i07304811

Diesel

Exhaust

Fluid

Injector

(Emission

Related

Component)

Replace

Illustration 82

g03363165

Typical example shown

Remove the diesel exhaust fluid (DEF) line (1)

from the injector (4).

Remove the coolant lines (2) from the injector.

Remove the electrical connector (3) from the

injector.

Remove the bolts from the injector and remove the

injector.

Replace gasket. The steel side of the gasket

should face towards diesel particulate filter (DPF)
outlet.

Replace the injector.

Apply anti-seize to bolt threads.

Torque the bolts of the injector to 5 N·m (3.7 lb ft).

Retighten all bolts to 5 N·m (3.7 lb ft), then turn
90°.

Connect the electrical connector.

10.

Connect the coolant lines.

11.

Connect the DEF line.

i07297232

Diesel

Particulate

Filter

(Emission

Related

Component)

Clean

Consult

your

Perkins

dealer

when

the

DPF

needs

cleaned.

The

approved

Perkins

DPF

maintenance

procedure

requires

that

one

the

following

actions

taken

when

the

DPF

needs

cleaned:

• The DPF from your engine can be replaced with a

new DPF

• The DPF from your engine can be replaced with a

remanufactured DPF

• The DPF from your engine can be cleaned by your

local authorized Perkins dealer, or a Perkins
approved DPF cleaning machine, and reinstalled

Note:

To maintain emissions documentation, the

DPF that is removed from the engine when the DPF
is cleaned must be reinstalled on the same engine.

Note:

A specific ash service regeneration must be

performed before removing a DPF that will be
cleaned. All three scenarios listed above require a
reset of the ash monitoring system in the engine
ECM.

i02151646

Driven

Equipment

Check

Refer

the

OEM

specifications

for

information

the

following

maintenance

recommendations

for

the

driven

equipment:

• Inspection

• Adjustment

• Lubrication

• Other maintenance recommendations

Perform any maintenance for the driven equipment
which is recommended by the OEM.

M0087475-03

Maintenance Section
Diesel Exhaust Fluid Injector (Emission Related Component) - Replace

Содержание 1706J-E93TA


































































































































Результаты поиска

Содержание 1706J-E93TA

Отзывы:

Perkins 1706J-E93TA, Руководство по эксплуатации и обслуживанию, Страница: 98 / 130

Результаты поиска

Содержание 1706J-E93TA

Отзывы: