Perkins 1706J-E93TA Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 130

Perkins 1706J-E93TA Скачать руководство пользователя страница 87

5.

Reinstall the belt guard, refer to OEM for the

correct procedure.

If new drive belts are installed, check the drive belt

tension again after 30 minutes of engine operation at
the rated rpm.

Belt Tension Chart

Table 17

New Belt Tension

Used Belt Tension

Reset Tension

801 N (180 lb)

645 N (145 lb)

378 N (84 lb)

Replace

To replace the fan belts, refer to Disassembly and
Assembly, V-Belts- Remove and Install.

i07297206

Coolant

Temperature

Regulator

-

Replace

Replace

the

water

temperature

regulator

before

the

water

temperature

regulator

fails.

Replacing

the

water

temperature

regulator

is

a

recommended

preventive

maintenance

practice.

Replacing

the

water

temperature

regulator

reduces

the

chances

for

unscheduled

downtime.

Refer

to

this

Operation

and

Maintenance

Manual,

“Maintenance

Interval

Schedule”

for

the

proper

maintenance

interval.

A

water

temperature

regulator

that

fails

in

a

partially

opened

position

can

cause

overheating

or

overcooling

of

the

engine.

A

water

temperature

regulator

that

fails

in

the

closed

position

can

cause

excessive

overheating.

Excessive

overheating

could

result

in

cracking

of

the

cylinder

head

or

piston

seizure

problems.

A

water

temperature

regulator

that

fails

in

the

open

position

will

cause

the

engine

operating

temperature

to

be

too

low

during

partial

load

operation.

Low

engine

operating

temperatures

during

partial

loads

could

cause

an

excessive

carbon

buildup

inside

the

cylinders.

This

excessive

carbon

buildup

could

result

in

accelerated

wear

of

the

piston

rings

and

wear

of

the

cylinder

liner.

NOTICE

Failure to replace your water temperature regulator
on a regularly scheduled basis could cause severe
engine damage.

Perkins engines incorporate a shunt bypass design
cooling system and require operating the engine with
a water temperature regulator installed.

If the water temperature regulator is installed incor-
rectly, the engine may overheat, causing cylinder
head damage. Ensure that the new water tempera-
ture regulator is installed in the original position. En-
sure that the water temperature regulator vent hole is

open.

Do not use liquid gasket material on the gasket or cyl-
inder head surface.

Refer to two articles in the Disassembly and
Assembly Manual, “Water Temperature Regulators -
Remove and Water Temperature Regulators - Install”
for the replacement procedure of the water
temperature regulator, or consult your Perkins dealer.

Note:

If the water temperature regulators are

replaced, drain the coolant from the cooling system
to a level that is below the water temperature
regulator housing.

i06606846

Cooling

System

Coolant

(DEAC)

-

Change

Clean

the

cooling

system

and

flush

the

cooling

system

before

the

recommended

maintenance

interval

if

the

following

conditions

exist:

• The engine overheats frequently.

• Foaming is observed.

• The oil has entered the cooling system and the

coolant is contaminated.

• The fuel has entered the cooling system and the

coolant is contaminated.

Note:

Inspect the water pump and the water

temperature regulator after the cooling system has
been drained.

M0087475-03

87

Maintenance Section

Coolant Temperature Regulator - Replace

«
...
85
86
87
88
89
...
»

Содержание 1706J-E93TA



































































































































Отзывы:

Нет отзывов