Perkins 1706J-E93TA Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 130

Perkins 1706J-E93TA Скачать руководство пользователя страница 85

All lead-acid batteries contain sulfuric acid which

can burn the skin and clothing. Always wear a
face shield and protective clothing when working
on or near batteries.

1.

Remove the filler caps. Maintain the electrolyte

level to the

“

FULL

”

mark on the battery.

If the addition of water is necessary, use distilled
water. If distilled water is not available use clean
water that is low in minerals. Do not use artificially
softened water.

2.

Check the condition of the electrolyte with a

suitable battery tester.

3.

Install the caps.

4.

Keep the batteries clean.

Clean the battery case with one of the following
cleaning solutions:

• Use a solution of 0.1 kg (0.2 lb) baking soda

and 1 L (1 qt) of clean water.

• Use a solution of ammonium hydroxide.

Thoroughly rinse the battery case with clean
water.

i05424317

Battery

or

Battery

Cable

-

Disconnect

The battery cables or the batteries should not be
removed with the battery cover in place. The bat-
tery cover should be removed before any servic-
ing is attempted.

Removing the battery cables or the batteries with
the cover in place may cause a battery explosion
resulting in personal injury.

1.

Turn the start switch to the OFF position. Turn the

ignition switch (if equipped) to the OFF position
and remove the key and all electrical loads.

Note:

After the engine has stopped, allow 2 minutes

in order for the diesel exhaust fluid lines to be purged
before disconnecting the power.

2.

Disconnect the negative battery terminal. Ensure

that the cable cannot contact the terminal. When
four 12 V batteries are involved, 2 negative
connections must be disconnected.

3.

Remove the positive connection.

4.

Clean all disconnected connection and battery

terminals.

5.

Use a fine grade of sandpaper to clean the

terminals and the cable clamps. Clean the items
until the surfaces are bright or shiny. DO NOT
remove material excessively. Excessive removal
of material can cause the clamps to fit incorrectly.
Coat the clamps and the terminals with a suitable
silicone lubricant or petroleum jelly.

6.

Tape the cable connections in order to help

prevent accidental starting.

7.

Proceed with necessary system repairs.

8.

In order to connect the battery, connect the

positive connection before the negative connector.

i07223806

Belts

-

Inspect/Adjust/Replace

(Alternator

Belt)

The

alternator

belt

adjustment

is

performed

by

an

automatic

tensioner.

Belt

tension

is

controlled

by

the

tensioner

and

no

manual

adjustment

will

be

required.

M0087475-03

85

Maintenance Section

Battery or Battery Cable - Disconnect

«
...
83
84
85
86
87
...
»

Содержание 1706J-E93TA



































































































































Отзывы:

Нет отзывов