Perkins 1706J-E93TA Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 130

Perkins 1706J-E93TA Скачать руководство пользователя страница 106

Illustration 89

g06257798

Typical example

3.

Clean sealing surface (2).

4.

Apply clean engine oil to O ring seal (3) for the new

oil filter.

NOTICE

Do not fill the oil filters with oil before installing them.
This oil would not be filtered and could be contami-

nated. Contaminated oil can cause accelerated wear

to engine components or engine damage.

5.

Install the new oil filter. Spin on the oil filter until the

O ring contacts the sealing surface (2). Then
rotate the oil filter ¾ of a full turn.

Fill the Oil Pan

1.

Remove the oil filler cap. Refer to this Operation

and Maintenance Manual, “Fluid
Recommendations” for more information on
suitable oils. Fill the oil pan with the correct
amount of new engine lubricating oil. Refer to this
Operation and Maintenance Manual, “Refill
Capacities” for more information on refill
capacities.

NOTICE

If equipped with an auxiliary oil filter system or a re-
mote filter system, follow the OEM or the filter manu-
factures recommendations. Under-filling or over filling
the crankcase with oil can cause engine damage.

2.

Start the engine and run the engine at

“

LOW IDLE

”

for 2 minutes. Perform this procedure to ensure
that the lubrication system has oil and that the oil
filters are filled. Inspect the oil filter for oil leaks.

3.

Stop the engine and allow the oil to drain back to

the oil pan for a minimum of 10 minutes.

Illustration 90

g02173847

“

L

”

Low

“

H

”

High

4.

Remove the engine oil level gauge to check the oil

level. Maintain the oil level between the

“

L

”

and

“

H

”

marks on the engine oil level gauge. Do not fill the
crankcase above the

“

H

”

mark.

i07257552

Engine

Storage

Procedure

-

Check

Engine

Perkins

recommends

storage

procedures

and

start-

up

procedures

for

all

engines

that

are

stored

for

more

than

1

month.

These

procedures

provide

maximum

protection

to

internal

engine

components.

An

extension

of

the

oil

change

interval

to

12

months

is

permitted

if

you

follow

the

required

procedures

for

storage

and

start-up.

This

extension

is

permitted

if

the

following

intervals

in

the

Operation

and

Maintenance

Manual,

“Maintenance

Interval

Schedule”

have

not

been

reached:

• Operating hours

• Fuel consumption

Perkins recommends the use of Volatile Corrosion

Inhibitors (VCI) oil to prevent internal engine damage
due to moisture during storage. These inhibitors act
by evaporating inside the engine, then condensing
over the inside surfaces.

106

M0087475-03

Maintenance Section
Engine Storage Procedure - Check

«
...
104
105
106
107
108
...
»

Содержание 1706J-E93TA



































































































































Отзывы:

Нет отзывов