Attaching The Receiver
Attaching the UltraElite or UltraMax receiver to
your collar is easy!
1. Place the collar holes over the receiver
inserts. Be sure the receiver case is on the
out side of the collar.
2. Install the plastic washers with the flat
side toward the probes.
3. Attach the probes by screwing them
snugly (preferably by hand) into the
receiver inserts.
The Receivers
Be careful not to over-tighten the probes. Over-tightening can cause damage to
the probes and receiver case.
If you wish to attach the receiver to a collar other than the one provided by your Pet Stop dealer, you
must create two holes for the receiver inserts, washers, and probes. Be sure the holes are correctly
sized to fit properly. After doing so, follow the above steps to attach the receiver to the collar.
Adjusting the Receiver Collar on your Pet.
It is important that the probes sufficiently make contact with the dog’s skin. One finger should fit
between the dog’s neck and a probe. Your Pet Stop dealer will demonstrate proper collar snugness.
Be sure to check the collar every few days for proper snugness. Your dog will not feel a correction if
the collar is too loose, and may escape from the yard. Always remove the receiver collar at the end
of the day when your pet is inside.
Battery Replacement
To replace the battery, remove the battery cover
with any flat-head screwdriver or a coin. Remove
the old battery and recycle it. Check with your local
municipality for recycling options. Insert the new battery
with the positive (+) end UP toward the battery cover.
If you are uncertain which side of the battery is the
positive side, look closely at the flat side of the battery.
You will see a plus (+) mark indicating the positive end.
Battery Maintenance
Battery maintenance is convenient and easy. Your Pet
Stop dealer can offer you a battery subscription plan
which will make the timing of battery replacement
hassle-free. With this plan, you will receive a battery in
the mail when it is time to replace it. Ask your Pet Stop
dealer for details.
Comfort Contacts
Probe Inserts
Plastic Backstrip
The receiver collar may
need adjustment due to
changes in your pet’s coat,
weight and age.
Your transmitter comes complete with these standard features:
Built-in Lightning Protection with Zapp Alert
®
Warning
Traditionally, lightning is one of the most common causes of transmitter failure. Pet Stop has
developed built-in surge and over-voltage protection for both the electrical outlet and any high
voltage carried by the buried wire in your yard.
To add extra protection for you and your pet, we have added Zapp Alert
®
, an audio-visual indication
feature should lightning damage your unit. If your transmitter experiences an electrical surge, the
transmitter will continue to sound two short beeps. If this happens, contact your local Pet Stop
dealer for service immediately.
Remember:
Do not allow your pet outside during a lightning storm.
Wire Break Warning System
Your transmitter also has a built-in sensor which monitors the boundary wire. If, for any reason,
the wire becomes broken, the transmitter display will flash and a continuous single beep will alert
you to the problem. Unplug the transmitter and contact your local Pet Stop dealer to assist you in
locating and repairing the wire break correctly.
Fully Adjustable Signal Field
Your transmitter is also completely adjustable. Press the up and down buttons located on the front
of the transmitter to adjust the signal field for your specific installation. Press the UP button to
increase the signal field width or press the DOWN button to decrease the signal field width. The
digital display has a range from 01 to 32. For example, if your range is set to 16 this indicates there
is 8 feet of signal field on either side of the boundary wire for a total of 16 feet.
Your Pet Stop dealer has set the signal field range appropriate for your installation.
Before adjusting the signal field width contact your dealer.
We recommend that your dog be on a leash or carefully supervised if the transmitter
is not functioning.
Turning the Transmitter On and Off
If you are going to be away for extended period of time and want to turn off the transmitter, press
the two black buttons simultaneously. To turn the transmitter back on, press the top button. It is
not necessary to reset the transmitter. Remember, when the transmitter is turned off, the Pet Stop
receiver collar will not activate.
The Transmitter
5
8
PS.OM.0708.indd 7
7/18/08 10:46:18 AM
