Pergola kits USA CLASSIC CEDAR PERGOLA KIT Скачать руководство пользователя страница 11

9

P a g e

 | 

25.

 

Check the other side of the runner. 
Be sure that the posts are plumb and 
the overhang is the same. Attach with 
another screw. Repeat this on the 
opposite end of the pergola, making 
sure that the overhangs are the same as 
with the first runner. Set the remaining 
runners in place and attach each of 
the runners to the front beam, while 
measuring each overhang. Repeat on 
the opposite beam. Be sure to check 
the overhangs on the back beam. 

Section 7 - Setting Top Runners 

26.

 

Notice that there are marks on top of 

the main runners where the top 
runners are to be attached. These 
markings are about 16" on center, or 
another dimension if the pergola was 
ordered with additional top runners. 
There are also markings and pre 
drilled holes on each of the 2x2 
runners. 

27.

 

Set the top markings on the centers of 
the runners, attach with 2½" screws. 
Check that the overhangs are the same 
on both sides of the top runners. 

On longer pergolas, the top runners will be in two pieces. They are cut so that when properly 
positioned the overhangs will be the same. You will want to position all the runners so that 
they are correctly positioned before attaching them.

Section 8 - Corner Braces 

28.

 

There will be 8 corner braces. 4 of them  

 

will be larger. These will go up in  

 

between the 2x8 headers. The smaller  

 

ones will go right underneath the return  

 

beams.

19.) Place the top runners at the pencil mark 
by the rafters, then put the pencil mark that 
is on top of the top runner at the side of the 
runners. Make sure  the “X” is on top of the 
runner. Next, check that the overhangs are the 
same on both sides of the top runners. Attach 
with 2½” screws, using (1) screw per rafter. 

NOTE: On longer pergolas, the top runners will 
be in two pieces. They are cut so that when 
properly positioned the overhangs will be the 
same. You will want to position all the runners 
first and check that they are correctly 
positioned before attaching them.

The Classic Freestanding Pergola is now complete.  If you purchased a canopy  with your 
pergola, follow the directions that are included with the canopy. 

If additional options (Lattice top, privacy panels or corner lattice) were ordered, a separate sheet 
of instructions is included. Be sure to call your project advisor with any questions. 

ENJOY YOUR NEW WOOD CLASSIC 

FREESTANDING PERGOLA

Содержание CLASSIC CEDAR PERGOLA KIT













Отзывы: