2
SAFETY GUIDELINES / DEFINITIONS
UNPACKING AND INSPECTION
SPECIFICATIONS
IMPORTANT SAFETY INFORMATION
Specifications are subject to change without notice
WARNING
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS
TOOL. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL
VOID WARRANTY.
1. Study, understand, and follow all instructions before operating
this device.
2. DO NOT exceed rated capacity. Overloading can cause dam-
age to or failure of the jack.
3. Use only on hard, level surface capable of sustaining the load.
Use of jack on other than hard level surfaces can result in jack
instability and possible loss of load.
4. Lifting device only. Immediately after lifting, support the vehicle
with appropriate means. Ensure that no personnel pass under-
neath load until load is securely supported by jack stands.
5. DO NOT adjust safety valve.
6. Wear ANSI approved safety goggles and heavy duty work
gloves during use.
7. Keep clear of load while lifting and lowering.
8. Lower load slowly.
9. DO NOT use for aircraft purposes.
10. Apply parking brake and chock tires before lifting vehicle.
11. Lift vehicle only at vehicle manufacturer recommended lift
locations.
12. Inspect before every use; do not use if parts are loose or
damaged.
13. Do not alter this product in any way.
14. Keep your work area clean and well lit. Cluttered work areas
invite accidents.
15. Keep bystanders, children, and visitors away while operating
jack. Distractions can cause you to lose control.
16. Stay alert. Watch what you are doing, and use common
sense when operating a jack. Do not use a jack while tired
Capacity: ........................................................................................................... 24,000 lbs.
Minimum Lift Height: .......................................................................................... 6 11/16 in.
Maximum Lift Height: ................................................................................................ 13 in.
Base Length: .......................................................................................................... 5 1/4 in.
Base Width: ............................................................................................................ 5 1/4 in.
Warning:
This is a lifting device only. Load must be supported immediately by Jack Stands.
WARNING:
Read and understand this entire instruction manual before attempting to assemble, install, operate or
maintain this hydraulic bottle jack. Failure to comply with the instructions may result in serious personal injury
and/or property damage!
The following signal words are used to emphasize safety warnings that must be followed when using this
hydraulic bottle jack:
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps
described within to ensure your safety and satisfaction. The contents of this instruction manual are based upon the latest product information
available at the time of publication. The manufacturer reserves the right to make product changes at any time without notice.
DANGER
Indicates an imminently hazardous situation that, if
not avoided, WILL result in death or serious injury.
WARNING
Indicates a potentially hazardous situation that, if
not avoided, COULD result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation that, if
not avoided, MAY result in minor or moderate injury.
NOTICE
Indicates important information, which if not followed,
MAY cause damage to equipment.
After opening the carton, unpack your new hydraulic bottle jack and related parts & accessories. Please inspect it
carefully for any damage that may have occurred during transit. Please check it against the photograph on carton. If
any parts are missing, please call customer service at 1-800-426-1262 between 6 a.m. and 5 p.m. Pacific time.
WARNING
DO NOT operate this hydraulic bottle jack if damaged during shipment, handling or misuse. Do not operate the hydraulic
bottle jack until the parts have been replaced or the fault rectified. Failure to do so may result in serious personal injury or property
damage. All damaged parts must be repaired or replaced as needed prior to operating this hydraulic bottle jack. Check to see that all
nuts, bolts and fittings are secure before putting this hydraulic bottle jack into service. If you have any questions, or require assistance
with damaged or missing parts, please contact our factory customer service department at: 1-800-426-1262.
Please have the serial number, model number, and date of purchase available for reference when calling.
