Performance Cruising Gemini 105Mc Скачать руководство пользователя | Manualshive

Страница: 29 / 59

background image

Gemini 105Mc Owner’s Manual

29

Copyright © 2004 Performance Cruising Inc.

Depending on the amount of usage, eventually it

is necessary to replace the steering cables. Per-
formance Cruising offers step-by-step instructions
on replacing the steering cables on the Owners’
Info Center website. (http://www.mypci.net)

The rudders are raised and lowered by a double

purchase rope pulley system. The operation of the
system is such that the rudders will steer at any
position – up, down, or in between. There is no

increase in tiller loads as the rudders are raised,
unlike most other systems.

The ropes that lower the rudders go through a

sheet stopper. The sheet stopper is made ineffi-

cient by the addition of another rope so that if the
rudder hits an under water obstruction it will kick

up. When not moving forward the rudders will
stay down, but when moving forward the rudders
tend to kick up. The sheet stopper prevents the

rudders from raising. However, do not over ten-

sion the stopper as the lines could jam and cause
breakage in the rudder system.

Be sure to lower the rudders when leaving the

boat, particularly in deep or choppy water. Leav-
ing the rudders in the up position for long periods
of time causes unnecessary strain on the up rope.

There are no holes drilled below the water line so

that even if the whole rudder were to be ripped
from the back of the boat there would be no holes
in the boat unlike any other system.

Access to the rudder mechanism is through the

hatch in the second transom step.

The drive leg is steered by ropes connected to the
end of the tillers that exit the transom by the
bridge deck and are then connected to the drive
leg.

For emergency steering another pad eye can be

fixed to the outside of the hull. With ropes to each

side of the tiller and then the ropes connected
together, a tiller can be connected to the two
ropes that will steer the boat by moving one rope
one way and the other rope the other way.

Centerboards and Rudders

«
...
27
28
29
30
31
...
»

Содержание Gemini 105Mc




























































Отзывы:

Нет отзывов

Похожие инструкции для Gemini 105Mc

Бренд: Bangor Punta Marine Страницы: 49

Бренд: Thaijetboard Страницы: 32

Mirage Eclipse 10.5

Бренд: Hobie Страницы: 20

Бренд: C&C Страницы: 34

Бренд: BAY SPORTS Страницы: 9

Бренд: Pakboats Страницы: 7

Бренд: Lagoon Страницы: 144

Бренд: MINN KOTA Страницы: 28

Бренд: Sailfish Страницы: 52

sun odyssey 33I

Бренд: Jeanneau Страницы: 136

SUN ODYSSEY 39DS

Бренд: Jeanneau Страницы: 118

Бренд: Manitou Страницы: 68

Бренд: whaler Страницы: 24

Бренд: Tyco R/C Страницы: 4

Бренд: CORRECT CRAFT Страницы: 244

Бренд: Intex Страницы: 12

2007 Moorings Beneteau 32.2

Бренд: ANDIAMO Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды