Read the ENTIRE manual before set up or use of this product.
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp
or wet locations. Don’t expose to rain. Keep work area well lighted. Do not
use electrically powered tools in the presence of flammable gases or
liquids. Do not bring combustible materials near the tools.
3. As with any tool, use common sense when operating. Do not wear loose
clothing or jewelry that could become caught by moving parts, causing
injury. Operate tool a safe distance from yourself and others in the work area.
4. Keep children away. Children must never be allowed in the work area. Do
not let them handle machines, tools, hoses or extension cords.
5. Store idle equipment. When not in use, tools must be stored in a dry
location to inhibit rust. Always lock up tools and keep out of reach of
children and other untrained persons. Switch off all unused electrical tools
when stored. Tools are dangerous in the hands of untrained users.
6. Always wear ANSI Z87 approved safety glasses when using tools.
If raising dust, wear a suitable mask.
7. Work Safe. When wearing gloves to operate the tool, make sure that the
gloves do not interfere with operating the Trigger. Test your gloves with the
Trigger before attaching the unit to an air source. Keep your finger away
from the Trigger until you are ready to work. Never start the tool unless
you have a firm grip with both hands and you are positioned at your work
piece or area. Before using the tool, know what is directly underneath the
work area or work piece. The tool can quickly penetrate material. If
working directly on the ground, make sure you are not directly above
shallow cables, lines, or pipes. Keep your limbs and body clear of the tool.
If an accessory or attachment breaks off, the tool tends to surge forward
suddenly. Operate tool a safe distance from yourself and others in the work
area. Make sure the immediate area is clear of other people or animals.
Spectators must stay at a safe distance. Never point the tool or the air hose
(not included) at anyone. Keep proper footing and balance at all times. Do
not reach over or across running machines, hoses, etc.
8. Do not operate any tool if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate any tool.
9. Be sure air is in OFF position when connecting tool to air supply.
10. Use only those accessories that are designed for use with tools. For
example, with impact wrenches do not use ordinary sockets. Use impact
sockets for all air tools.
11. Be sure to disconnect tool from air supply before changing accessories,
performing service on tool and when not in use.
12. Follow air source manufacturers’ directions for connection of regulators,
filters, and other accessories to air source. Do not install quick couplers
directly on tool as they put unnecessary strain on the air inlet threads
possibly causing them to wear out prematurely. Instead, install them on a
short length of air hose attached to the tool.
13. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment and
binding of moving parts; any broken parts or mounting fixtures; and any
other condition that may affect proper operation. Any part that is damaged
should be properly repaired or replaced by a qualified technician.
14. Maintenance. For your safety, maintenance should be performed regularly
by a qualified technician using original replacement parts. Failure to do so
can lead to accidents for the operator. Use of any other parts will void the
warranty. Only use accessories intended for use with this tool. Use only
accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when
used on another tool.
WARNING:
Repetitive motions or exposure to vibration may be harmful to
your hands and arms.
WARNING:
This product and its packaging contain a chemical known to the
State of California to cause cancer, birth defects, or other reproductive harm.
WARNING:
The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
operator. Read and understand all of the instructions provided in the instruction
manual of this product, as well as, any other tool (s) used with this product.
Specifications are subject to change without notice.
2
SPECIFICATIONS:
1/2" Air Ratchet
Square Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 in.
Working torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50 ft./lbs.
Air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 PSI
Average air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CFM
Free speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 RPM
Bolt capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 in.
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4 NPT
Hose size (I.D.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8 in.
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.65 lbs./1.2 kg
Impact Wrench
Drive Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 in.
Max Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 ft/lbs.
Working Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50-200 ft/lbs.
Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 PSI
Average Air Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CFM
Free Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,500 RPM
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4 NPT
Hose size (I.D.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8 in.
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.4 lbs./2 kg
Air Hammer
Bore Size ......................................................................................... 3/4 in.
Stroke Length .................................................................................. 1.7 in.
Air Pressure .....................................................................................90 PSI
Average Air Consumption .............................................................. 4 CFM
Free Speed ............................................................................... 4,500 BPM
Air Inlet ........................................................................................... 1/4 in.
Hose Size (ID) ................................................................................. 3/8 in.
Length ............................................................................................. 5.1 in.
Weight ....................................................................................2.2 lbs./1 kg
Die Grinder
Collet Size ................................................................................ 1/8, 1/4 in.
Air Pressure .....................................................................................90 PSI
Average air consumption ............................................................... 4 CFM
Free speed ............................................................................. 22,000 RPM
Air inlet ........................................................................................1/4 NPT
Hose size (I.D.) ............................................................................... 3/8 in.
Length ............................................................................................. 6.8 in.
Weight .................................................................................1.3 lbs./.59 kg
SPECIFICATIONS
IMPORTANT SAFETY INFORMATION
