On the front of each leg are two holes
for skirt mounting brackets. Locate
the two brackets and attach them as
shown with two #10-32 x 1/2” screws
and two #10-32 locking nuts each.
12
Attach the sirt as shown by
inserting the tabs along the top
of the skirt into the slots in the
bottom of the bench cover and
placing the bottom edge into the
skirt mounting brackets. Adjust
the skirt mounting brackets up or
down to secure the skirt.
13
Using Your Sunbed
Before using your sunbed, please note the following:
• Your skin should be free of cosmetics, tanning oils, or other body
lotions prior to tanning except for those specifically made for use
with tanning devices. However, do not remove natural body oils by
bathing or showering immediately before tanning.
• Keep treated hair from contacting sunbed surfaces. Many hair prod-
ucts can damage the sunbed acrylic. Wear a shower cap or towel if
you use gels, mousses, sprays, or other hair products.
• Your sunbed is designed for individual use. Always wear the safety
goggles supplied with your sunbed or another approved pair of gog-
gles, as defined under 21 CFR 1040.20. Regular sunglasses do not
provide adequate protection from ultraviolet light.
Exposure Times
Follow the guidelines for skin type and exposure times as shown in the
table on the first page. Untanned persons should not tan on consecutive
days during their first week of tanning. Never tan more than once a day.
Tanning normally appears after the first few sessions and maximizes
after approximately four weeks. Tan once or twice per week thereafter
to maintain appearance. Persons already having a base tan may begin at
advanced levels corresponding to the extent of their base tan.
A Timer display
- Displays remaining time.
B Timer button
- Turns bed on. Timer dis-
play shows remaining time. If a lesser
time is desired, press timer button
until desired time is displayed.
C Stop button
- Interrupts tanning session.
1
Press the timer button (B) to begin the tanning session. The timer dis-
play (A) displays the remaining time. The lamps will turn on and the
timer will begin to count down from the maximum tanning session
time. If a tanning time less than the displayed time is desired repeat-
edly press the timer button (B) to decrease the remaining time.
2
Lift the canopy, lie down on the bench (face up), lower the canopy
as close to your body as possible, with no less than 2” between the
canopy acrylic and your body.
3
When the timer reaches “0” the lamps turn off. If you want to stop
your session before time expires, press the stop button (C).
4
Raise the canopy by pushing the outer edge of the canopy.
Operation
A
B
C
Care and Maintenance
Cleaning After Use
Clean and disinfect your tanning bed’s bench and canopy after each
use. Use a non-abrasive disinfectant cleaner that
does not contain
ammonia or ammonia derivatives
. Ammonia may damage the acrylic
shield. Spray the acrylic lightly with disinfectant and wipe dry with a
clean soft cloth.
Thorough Periodic Cleaning
The cooling fans draw air through the bed and will cause a dust
buildup on the lamps and reflectors. When a dust buildup is observed,
it is necessary to thoroughly clean the inside of the bench and canopy.
1
Remove the acrylic shields and lamps.
2
With a soft cloth, wipe the entire length of each lamp.
3
Clean both sides of the acrylic shields with a non-ammonia dis-
infectant cleaner.
4
Wipe the reflectors with a clean damp cloth.
5
Re-install the lamps and acrylic shields.
Mechanical Inspection
Inspect the unit’s mechanical integrity every 400-500 hours of use.
• Inspect the unit’s fasteners verifying that all are firmly in place.
Pay particular attention to the hinge bolts.
• Inspect gas springs for signs of wear. Replace gas springs that will
not hold the canopy in the full open position when raised.
• Inspect the AC power cord and its connections.
• Inspect the acrylic. Replace if broken, cracked or badly scratched.
Replacing Lamps
To be assured of maximum tanning effectiveness, change lamps after
approximately 800-1000 hours of use. Tanning will continue after this
time but at a slower rate. To ensure trouble-free operation of your
sunbed, replace the lamp starters whenever the lamps are replaced. We
recommend using the lamps specified in the Safety Information. Use
of uncertified lamps is a violation of Federal regulations and will void
your warranty.
1
Grasp a lamp at one end and at the middle, then turn the lamp a
quarter turn. The lamp may then be gently removed from its holder.
2
To reinstall lamp, insert pins on the ends of the lamp into the slots
on top of the lamp holder and turn the lamp a quarter turn.
Removing/Replacing Acrylic Shields
The acrylic shields are secured in place by hinged profiles which run
the length of the bed, both front and back. Simply pry up on the inside
edge of the profile until it releases its latching action (see figure
below). Continue to pry up the profile across its entire length until it
swings back freely. Repeat for the other profile. The long edges of the
acrylic shield are now exposed. Standing in front of the sunbed, grasp
the long exposed edge of the acrylic and carefully slide it toward you
until it is removed.
After changing the lamps, replace
the acrylic shields by reversing
the above directions. Close the
hinged profile by pushing it
back into place until it snaps
tight.
PROFILE
CAUTION
Be careful. The edges of the
acrylic shield may be sharp.
Start pulling from the
middle of the profile!
