11
12
8. When the waveband end is reached, the radio will recommence tuning from the
opposite waveband end.
Manual tuning – FM
1. Press the
On/Off button
to turn on the radio.
2. Select the FM band by pressing the
Source button
.
3. Rotate the
Tuning knob
to reach the preferred FM station. The radio will change
the frequency in steps of 50 kHz.
4. Rotate the rubber antenna to get the best reception. If the radio is tuned to a
station of sufficient signal strength with RDS information present, the display may
change to show the station name. 5. When the waveband end is reached, the radio
will recommence tuning from the opposite waveband end.
RDS station service – FM
RDS (Radio Data System) is an information system which inaudible digital information
is transmitted in addition to the normal FM radio program. When the radio is receiving a
RDS station and the reception strength is sufficient, the station name will appear in the
display. It may take some time before the RDS information is available.
Calling up RDS information
When you are listening to a FM station with RDS system, repeatedly press the
Info
button
to cycle through the information. This will only function if the reception level is
sufficient and clear.
a. Radio text (RT)
Displays the message about the station being listened to as
ticker text.
b. Program type (PTY) Displays the type of station being listened to, e.g. Pop, Classic,
News, etc.
c. Frequency
Displays the frequency of the station being listened to.
d. Stereo or Mono
Displays Stereo or Mono.
e. Signal level
Displays the signal strength.
f. Time & date
Displays the current time (24 hour clock) and date.
Scan sensitivity setting – FM
The radio will normally scan all stations from FM broadcasts including the weaker
signals. However, you may wish the Auto-scan to find only those stations with strong
enough signals to give good reception.
1. Press the
On/Off button
to turn on the radio.
2. Select the FM band by pressing the
Source button
.
3. Press the
Menu button
, the display shows “Scan setting”.
4. Press the
Tuning knob
.
5. Rotate the
Tuning knob
to select between “All stations” or “Strong station”
(default is “All stations”). The “Strong station” option will allow the radio to find
strong signals only when scanning.
6. Press the
Tuning knob
to confirm your setting. The display will return to
normal radio display.
PRESET STATIONS
Storing preset stations
There are 20 memory presets in the radio, 10 for DAB and 10 for FM. Presets are
remembered by the radio in the event of a power failure.
1. Press the
On/Off button
to turn on the radio.
2. Press the
Source button
to select the desired waveband.
3. Tune to the required station.
4. Press and hold the required
Preset button
until the radio beeps and shows “Saved”.
5. Repeat step 3 and 4 for the remaining presets.
6. Stations stored in the preset memories can be over-written by following the
above procedure.
Recalling preset stations
1. Press the
On/Off button
to turn on the radio.
2. Press the
Source button
to select the desired waveband. Briefly Press the required
Preset button
.
3. In FM mode the display will show for example ”P1” on top right hand side.
MANUALLY SETTING CLOCK
The clock can only be manually set when the radio is in standby mode. If no buttons are
pressed for 5 seconds, the radio will exit the clock setup and the setting is cancelled.
1. Press and hold the Time Set knob for 12 seconds until the hour digits flash on the
display.
2. Rotate the
Time Set knob
to set the hour.
3. Press the
Time Set knob
to confirm, the minute digits flash.
4. Rotate the
Time Set knob
to set the minute.
5. Press the
Time Set knob
to confirm, the day flashes on the display.
6. Rotate the
Time Set knob
to set the current day.
7. Press the
Time Set knob
to confirm, the month flashes.
8. Rotate the
Time Set knob
to set the current month.
9. Press the
Time Set knob
to confirm, the year will then flash on the display.
10. Rotate the
Time Set knob
to set the current year.
11. Press the
Time Set knob
to confirm, “SYNCLOCK ON” flashes.
12. Rotary the
Time Set knob
to select “SYNCLOCK ON” or “SYNCLOCK OFF”.
13. Press the
Time Set knob
to confirm and finish the clock setting.
GB
