Perfect Flame 720-0335 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 31

Perfect Flame 720-0335 Скачать руководство пользователя страница 14

14

12.

Side Shelf Front Panel Assembly

Attach the side shelf front panel (16-1) to the side shelf (16-
2) with 4

–

5/32" x10mm truss head screws from pack A as

shown in fig. 16.

13.

Side Burner Control Panel Assembly

Attach the side burner bowl assembly (17-1) to the control
panel (17-2), use 4

–

5/32" x 10mm truss head screws from

pack A as shown in fig. 17.

14.

Side Shelf Assembly

Before left side shelf and right side burner assembly, remove
the screws and washers from the control panel left (18-1) and
right corners (18-2) as shown in fig. 18.

Attach the left side shelf (19-1) to the grill cart (19-2) using 4 -1/4

″

x 10mm truss head screws from pack E, 4 -1/4

″

locking washers

from pack G and 4

–

1/4

″

locking washers from pack D as shown

in fig. 19.

Attach the right side burner shelf (19-3) to the grill cart (19-2)
using 4

–

1/4

″

x 10mm truss head screws from pack E, 4 -1/4

″

flat

washers from pack G and 4 -1/4

″

locking washers from pack D as

shown in fig. 19.

Fig. 16

Fig. 17

(16-1)

(16-2)

(17-1)

(17-2)

Fig. 18

Fig. 19

(19-1)

(19-3)

(19-2)

(18-1)

(18-2)

PDF

文件使用

"pdfFactory Pro"

试用版本创建

www.fineprint.cn

«
...
12
13
14
15
16
...
»

Содержание 720-0335
































Отзывы:

Нет отзывов