TIMER operation
If setting the timer when the unit is on:
First press the TIMER button; the TIMER OFF
indicator light illuminates. It indicates the Auto Stop
program is initiated. Press the TIMER button again;
the TIMER ON indicator light illuminates. It
indicates the Auto Start program is initiated.
If setting the timer when the unit is off:
First press the TIMER button; the TIMER ON
indicator light illuminates. It indicates the Auto Start
program is initiated. Press the TIMER button again;
the TIMER OFF indicator light illuminates. It
indicates the Auto Stop program is initiated.
- Press or hold the UP or DOWN button to change
the Auto time by 0.5 hour increments, up to 10
hours, then at 1 hour increments up to 24 hours.
The control will count down the time remaining
until start.
- The selected time will register in 5 seconds and
the system will automatically revert back to
displaying the previous temperature setting.
- Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel the
Auto Start/Stop timed program.
- When a malfunction (E1-E2-E3-E4) occurs, the
AutoStart/Stop timed program will also be canceled.
6
OPERATING INSTRUCTIONS
- Press the "MODE" button until the "COOL"
indicator light comes on.
- Press the ADJUST buttons “+" or “–” to
select your desired room temperature. The
temperature can be set within a range of
62
O
F-88
O
F/17
O
C-30
O
C.
- Press the "FAN" button to choose the
fan speed.
- Press the "MODE" button until the "DRY"
indicator light comes on.
- Under this mode, you cannot select a fan speed
speed or adjust the temperature. The fan motor
operates at LOW speed.
- Keep windows and doors closed for
dehumidifying effect.
- Remove exhaust hose. (See page 11.)
COOL operation
DRY operation
- Press the "MODE" button until the "FAN"
indicator light comes on.
- Press the "FAN" button to choose the fan
speed. The temperature cannot be adjusted.
- Remove exhaust hose. (See page 11.)
FAN operation
- Press the "MODE" button until the "HEAT"
indicator light comes on.
- Press the ADJUST buttons “+" or “–” to
select your desired room temperature. The
temperature can be set within a range of
62
O
F-88
O
F/17
O
C-30
O
C.
- Press the "FAN" button to choose the fan
speed. For some models, the fan speed
can not be adjusted under HEAT mode.
- Remove exhaust hose. (See page 11.)
HEAT operation
E1- Room temperature sensor error
-
Unplug the unit and plug it back in.
If error repeats, call customer service.
E2- Evaporator temperature sensor error
-
Unplug the unit and plug it back in.
If error repeats, call customer service.
E4- Display panel communication error
-
Unplug the unit and plug it back in.
If error repeats, call customer service.
P1- Bottom tray is full
- Connect the
drain hose and drain the collected
water away. If error repeats, call
customer service.
Error and protection codes:
FOLLOW ME
AUTO operation
- When you set the air conditioner in AUTO mode,
it will automatically select cooling, heating
or fan only operation.
- The air conditioner will control room temperature
automatically around the temperature point you
have set.
- Under AUTO mode, you cannot select the
fan speed.
This feature can be activated from the remote
control ONLY. The remote control serves as a
remote thermostat allowing for the precise
temperature control at its location.
To activate the FOLLOW ME feature, point the
remote control towards the unit and press the
FOLLOW ME button. The light on the unit control
panel will illuminate to indicate it received the
signal. It will continue to send this signal to the air
conditioner every 3 minutes until the feature is
deactivated by pressing the FOLLOW ME button
again. If the unit does not receive the Follow Me
signal during any 7 minute interval, the unit will
beep to indicate the Follow Me mode has ended.
The display on the remote control indicates the
temperature at the remote ONLY.
