PERCo TTD-08A Скачать руководство пользователя страница 5

Страница: 5 / 38

Assembly & Operation Manual

TECHNICAL SPECIFICATIONS

Operating voltage .............................................................................................. 12±1.2VDC

Consumption current ........................................................................................... max. 6.0 A

Power consumption .......................................................................................... max. 72 W

Throughput rate in a single passage mode .................................................. 30 persons/min

Throughput rate in a free passage mode ..................................................... 60 persons/min

Passage width ......................................................................................................... 560 mm

Barrier arm rotation force ..................................................................................... max. 3 kgf

RC panel cable length

Ingress Protection Rating .......................................................................... IP44 (EN 60529)

...................................................................................... min. 6.6 m

Electric shock protection class ...................................................................... III (IEC 61140)

Mean time to failure .................................................................... min. 1,500,000 passages

Mean lifetime ........................................................................................................... 8 years

Overall dimensions (L × W × H) ......................................................... 1166×750×1016 mm

Net weight of the turnstile .................................................................................. max. 70 kg

Figure 1 – Overall dimensions of the TTD-08A turnstile

The power consumption can rise to 72W within 5 sec. after power up or at taking off the

Fire

Alarm

signal. In normal state the power consumption is no more than 30 W.

Max. allowed cable length – 40 m (supplied on request).

Содержание TTD-08A







































Результаты поиска

Содержание TTD-08A

Отзывы:

Похожие инструкции для TTD-08A

Бренды по названию

Популярные бренды

PERCo TTD-08A, Руководство по сборке и эксплуатации

Результаты поиска

Содержание TTD-08A

Отзывы:

Похожие инструкции для TTD-08A

Бренды по названию

Популярные бренды