background image

 
 

http://www.pepwave.com 

30 

Copyright @ 2010 Pepwave 

 
 

User Manual 

Pepwave PolePoint Series 

Appendix 

Federal Communication Commission Interference Statement 

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful 

interference in a residential installation.  This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications.  However, there is no guarantee that interference will not occur in a particular 

installation.  If this equipment does cause harmful interference to radio or television reception, which can 

be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one of the following measures: 
 
1) Reorient or relocate the receiving antenna. 
2) Increase the separation between the equipment and receiver. 
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
4) Consult the dealer or an experienced radio/TV technician for help. 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation. 

 

FCC Caution: Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user's authority to operate this equipment. 

 

IMPORTANT NOTE 
 
FCC Radiation Exposure Statement 

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 

This equipment should be installed and operated with minimum distance 20cm between the radiator & 

your body. 
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 
 

Содержание Surf 400-DX
































Отзывы: