Pepwave CarFi 200 Скачать руководство пользователя страница 4

Страница: 4 / 27

PePWave Surf/Mesh Connector/CarFi Series User Manual

Page 4

Product Description

It associates to a service provider and authenticates using 802.1x (if needed) on start up.

Upon successful association and authentication, it will acquire an IP address from the

service provider using DHCP. A DHCP server is built-in on its LAN port. Network Address

Translation is performed for all outbound connections. Thus it supports multiple terminals

to access the Internet simultaneously.

3.1

Features

—

10/100 Ethernet interface with auto-crossover detection

—

Reset button for restoring settings to factory defaults

—

Signal strength LED for showing the current signal strength (Applicable to PePWave

Surf indoor and DX series)

—

WPA/WPA2-Personal and WPA/WPA2-Enterprise support

—

Network Address Translation (NAT) routing

—

Built-in DHCP server

—

Inbound port range forwarding

—

Integrated Wi-Fi Access Point (Applicable to Surf AP indoor/outdoor and CarFi series)

Surf 200, AP 200, AP 400

Surf AP 200-X/400-X,

MC 200-X, 400-X

Surf 400-DX

MC 200, 400

CarFi 200, 400

Содержание CarFi 200




























Результаты поиска

Содержание CarFi 200

Отзывы:

Похожие инструкции для CarFi 200

Бренды по названию

Популярные бренды

Pepwave CarFi 200, Руководство пользователя

Результаты поиска

Содержание CarFi 200

Отзывы:

Похожие инструкции для CarFi 200

Бренды по названию

Популярные бренды