background image

PMI360DV-F130-IU-V15

Troubleshooting

 2

02

0-

01

19

9

Troubleshooting

9.1

Faults when programming the output

If unexpected situations occur when the output of the inductive angular positioning system is 

programmed, refer to the table below for possible causes and instructions for rectifying the 

problem.

State

Possible cause

Action

Sensor cannot be moved in 

programming mode (relevant 

yellow LED does not flash 

when a button is pressed).

Button not pressed long 

enough.

Press the button for program

-

ming the output 

 2 s.

Sensor cannot be moved in 

programming mode 

("Power/Error" LED lights up 

red).

No actuator available or own 

actuator mounted too far away 

from the surface of the sensor.

Mount actuator according to 

specifications (see chapter 

5.2).

"Power/Error" LED lights up 

red during programming.

Actuator lost during the 

parameterization process or 

distance between actuator 

and surface of sensor too 

great (own actuator).

Make sure that the concentric

-

ity and adjustment of own 

actuator does not result in a 

loss of the actuator (see chap

-

ter 5.2).

LED stops flashing during the 

programming process.

Timeout while programming 

the output (1 minute after the 

last input).

Move sensor again in pro

-

gramming mode ( or )

After programming, the func

-

tion of the output/outputs 

remains unchanged.

Programming process not 

completed within the time 

frame (1 minute) or incorrect 

button pressed during pro

-

gramming.

Complete the programming 

process by pressing the corre

-

sponding button for the output 

a third time within the time 

frame ( or )

A yellow LED flashes and the 

"Power/Error" LED flashes red 

at the same time.

The button assigned to the 

flashing yellow LED is stuck.

Remove any dirt or foreign 

objects that are causing the 

key to stick.

Содержание PMI360DV-F130-IU-V15























Отзывы: