Pepperl+Fuchs IUH-F117-V1-CN страница 26 Скачать руководство пользователя

Страница: 26 / 50

-0

IUH-F117-V1-*

Commissioning

6.2

Device Settings

Before commissioning the read/write head, the control interface must first be

configured. To do so, refer to the "Commissioning" chapter of the manual for your

control interface.

Configure the read/write heads with the described system commands (see

chapter 7.5.2). For a parameterization example, see see chapter 6.3.

6.3

Operation via the Command Interface

This section shows you how to operate the IUH-F117-V1 read/write head using an

IDENTControl control interface with serial interface. The commissioning

procedure described relates to the RS 232 interface and involves a PC. The

examples include the syntax for coding the commands and parameters via the

Ethernet TCP/IP and PROFIBUS interface. Further details about these codes and

the factory settings for your IDENTControl control interface can be found in the

manual.

<SystemCode>:

= U (for read/write head IUH*)

<TagType>:

2 ASCII characters

<UII/EPC>:

Unique Item Identifier, memory area of a tag in accordance with EPC

Gen 2 (ISO/IEC 18000-63), in which the EPC code is stored

<WordAddr>:

Word start address in the read/write tag, 4 hex

ASCII

characters, range

from "0000h" to "FFFF", depending on tag type

<WordNum>:

Number of words to be read or written, 2 hex

ASCII

characters. Range

from "01" through "20" depending on the tag type, word lengths are 4

bytes

Warning!

Device not configured or configured incorrectly

Configure the device prior to commissioning. A device that has not been

configured or configured incorrectly may lead to faults in the plant.

Caution!

Uncontrolled triggered processes

Before commissioning the device, make sure that all processes are running

smoothly; otherwise damage may occur in the plant.

Note!
Hexadecimal Display

In the examples, hexadecimal values are shown in the format .xx. A decimal point

is followed by 2 characters of hexadecimal code.
.03 = <ETX>
.41 = A

ASCII

Содержание IUH-F117-V1-CN



















































Результаты поиска

Содержание IUH-F117-V1-CN

Отзывы:

Похожие инструкции для IUH-F117-V1-CN

Бренды по названию

Популярные бренды

Pepperl+Fuchs IUH-F117-V1-CN, Руководство пользователя

Результаты поиска

Содержание IUH-F117-V1-CN

Отзывы:

Похожие инструкции для IUH-F117-V1-CN

Бренды по названию

Популярные бренды