Pepperl+Fuchs HiC2873 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

Pepperl+Fuchs HiC2873 Скачать руководство пользователя страница 8

2

01

9-

07

8

Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877

Product Description

HiC2873Y1

This device is a 1-channel device.
The device is bus powered.
The device is controlled with a switch contact, transistor, or logic signal.
At full load, 12 V at 40 mA (with 55 mA current limit) is available for the hazardous

area application.
This device mounts on a HiC termination board.

HiD2876

This device is a 2-channel device.
The device is loop powered or bus powered.
It is controlled with a loop powered control signal, switch contact, transistor, or logic signal.
At full load, 11.2 V at 40 mA (with 55 mA current limit) is available for the hazardous

area application.
An alternative low current output is available for driving a single LED without installing

an external current limiting resistor.
This device mounts on a HiD Termination Board.

HiC2877

This device is a 1-channel device.
The device is loop powered or bus powered.
It is controlled with a loop powered control signal, switch contact, transistor, or logic signal.
At full load, 11.2 V at 40 mA (with 55 mA current limit) is available for the hazardous

area application.
This device mounts on a HiC termination board.

«
...
6
7
8
9
10
...
»

Содержание HiC2873

























Отзывы:

Нет отзывов