Pepperl+Fuchs FD0-VC-Ex4.FF Скачать руководство пользователя страница 54

Страница: 54 / 60

Fieldbus Valve Coupler FD0-VC-Ex4.FF

Resource block

Subject to reasonable modifications due to technical advances.

Fuchs Group • Tel.: G49 621 776-0 • USA +1 330 4253555 • Sin65 67799091 • Internet http://www.pepperl-fuchs.com

082

, D

f i

ssue

3.2

006

Resource block

The column "Char." shows which characteristics or conditions are applicable to this parameter. The follow-
ing is applicable here:

•

OOS (Out of Service)

The parameter can be written only if the target mode of the block is "Out of Service".

•

S (Static)

During each writing process to such an identified parameter the parameter ST_REV is increased by one.

•

W (Writeable)

The parameter can be modified by the user.

As all parameters can be read this is not marked especially.

Parameter

Char.

Description

ST_REV

During each writing process to a parameter marked by "S" the parameter
ST_REV is increased by one.

TAG_DESC

W
S

Via this parameter the valve interface can be assigned a tag (measuring point
designation) within the plant and/or process.

STRATEGY

W
S

The strategy field can be used to identify comprising blocks. These data are
not controlled or used by the block.

ALERT_KEY

W
S

Identification number of the plant unit. This information can be used by the con-
trol computer, e.g. to sort alarms. Valid values are 1 ... 65536.

MODE_BLK

W
S

Displays the current, allowed normal mode and the target mode of the block.
The target mode can be set to the values "Auto" or "Out of Service".

BLOCK_ERR

Displays diagnosis messages of the block.

RS_STATE

Current status of device.

TEST_RW

Test parameter. Is used to test the device.

DD_RESOURCE

FF standard parameter. Not used.

MANUFAC_ID

Identification number of the device manufacturer - is used by the control sys-
tem to assign the device description (DD) to the device.

DEV_TYPE

Device type - is used by the control system to assign the device description to
the device.

DEV_REV

Version number of the device - is used by the control system to assign the
device description to the device.

DD_REV

Version number of device description - is used by the control system to assign
the device description to the device.

GRANT_DENY

Regulates the access rights between control system and local operator's sta-
tions for some control systems.

HARD_TYPES

Hardware type.

RESTART

Allows to carry out a new manual start. Different types of re-starts are possible:
There are
• Restart Resource,

• Restart with defaults (default settings),

• Restart processor.

FEATURES

Displays the options supported by the device. These are:
Unicode Strings

Unicode string,

Reports

Alarms,

Fault State

Release of the safe state for the whole device by the
resource block,

Hard Write lock

Hardware read-only feature,

Output Readback

Back-reading of the valve position via the PFCs.

FEATURE_SEL W

The options used are selected here.
See FEATURES.

CYCLE_TYPE

Gives the different block implementation methods for this device.

Содержание FD0-VC-Ex4.FF





























































Результаты поиска

Содержание FD0-VC-Ex4.FF

Отзывы:

Похожие инструкции для FD0-VC-Ex4.FF

Бренды по названию

Популярные бренды

Pepperl+Fuchs FD0-VC-Ex4.FF, Руководство пользователя

Результаты поиска

Содержание FD0-VC-Ex4.FF

Отзывы:

Похожие инструкции для FD0-VC-Ex4.FF

Бренды по названию

Популярные бренды