background image

5

FINAL BACKFILL FOR BASIN SYSTEMS

Polyethylene

Fiberglass

Risk of electrical shock or 

electrocution. May result 

in serious injury or death or 

fire hazard. To reduce risk of 

electrical shock, do not connect 

conduit to pump .

Step 1:

If the system is supplied with a 

float bracket, attach float switches to  

the float bracket by clamping 

 

strain relief bushings around the 

float cords, then inserting and 

twisting the bushings into the float 

bracket slots.

Step 2:

After grinder pump attachments 

have been made, lower the pump 

unit down and ensure the ball check 

valve sealing flange aligns and  

connects properly with discharge.

Junction Box Systems:

Step 1: 

Ensure power source is off or  

dis con nect ed.

Step 2: 

Push pump power, seal failure/heat 

sensor, and float cords through 

cord grips in the junction box and 

tighten. To prevent corrosion or 

electrical short, plug any unused 

holes.

Step 3: 

Remove junction box cover 

and make all connections inside 

junction box to all incoming 

control panel wires.

Step 4:

It is recommended that the 

customer furnish and install a 

conduit seal outside the basin 

to prevent surface water from 

entering the junction box.

Electrical Connections:

NOTE: Failure to use a 

Hydromatic approved control 

panel voids the pump warranty 

and guarantee.

IMPORTANT: Properly 

connect the panel ground wire 

to a grounding rod. Improper 

grounding voids warranty.

Panel Wiring:

Step 1: 

Ensure power source is off or 

disconnected.

Internal Basin 

Connections 

Содержание Hydromatic TG-Pro System













Отзывы: