Pentair FLECK 9100 SXT Скачать руководство пользователя страница 56

Страница: 56 / 108

Installer manual Fleck 9100 SXT - Programming

56 / 108

Ref. MKT-IM-004 / E - 06.10.2020

6.6

Diagnostic

Info

Depending on current settings, some displays cannot be viewed.

If none of the buttons are pushed for 1 minute in the diagnostic mode the controller
returns to Service mode.

6.6.1

Commands

1. Press and hold

and

for five seconds to enter the diagnostic mode.

2. Press

to navigate in the diagnostic mode.

3. Press

to exit the Diagnostic mode at any time.

6.6.2

Current flow rate (FR)

Info

The display is updated every second.

1. Current flow rate display (L/min or gpm depending on display format

programmed):

6.6.3

Peak flow rate (PF)

Info

The controller registers the highest flow rate (L/min) since the last regeneration.

1. Peak flow rate display:

6.6.4

Hours since last regeneration (HR)

Info

Shows the number of hours since the last regeneration, indicating the length of the
current service cycle.

1. Hours since last regeneration display:

Содержание FLECK 9100 SXT













































































































Результаты поиска

Содержание FLECK 9100 SXT

Отзывы:

Похожие инструкции для FLECK 9100 SXT

Бренды по названию

Популярные бренды

Pentair FLECK 9100 SXT, Руководство по установке

Результаты поиска

Содержание FLECK 9100 SXT

Отзывы:

Похожие инструкции для FLECK 9100 SXT

Бренды по названию

Популярные бренды