background image

The PSHC controls the QREV performance. The PSHC includes an internal MEMS pressure sensor. Install

the PSHC at the outlet of the evaporator on a 1/4 in. SAE access valve, and connect the PSHC to the

QREV with a 1.5 m (4.9 ft.) wiring harness with an integral temperature sensor. The PSHC monitors the

pressure and temperature at the evaporator coil outlet and adjusts the signal to the QREV to control flow

volume through the QREV and maintain the target superheat temperature.

Note: 

The QREV, PSHC, and wiring harness are available as individual items and you must purchase

each item separately.

You can apply the QREV and PSHC in most HVACR applications that use any of the 18 approved

refrigerants. The capacity can be fractional values. Figure 3 shows the 01 to 05 models, Figure 4 shows

the 06 to 08 models, and Figure 5 shows the 09 to 15 models.
The following applications are ideal for the QREV and PSHC:
• Refrigerated display cases, both self-contained and with remote condensers
• Commercial refrigerators and freezers
• Heat pumps
• Walk-in coolers and freezers
• HVAC systems
• Chillers
Table 1 explains the naming convention for the QREV model numbers, using the example code

QREV01-24SC-C.

Table 1: QREV product code matrix

Feature

Code letter or number and description

Product code example: QREV01-24SC-C

Family code

QREV

QREV

01–08

Sequence Code

09–15

01

12 = 12 VDC

Valve voltage

24 = 24 VDC/VAC

24

Valve body type

S = Straight Body Connection

Engineering version

C = Alpha character

SC

Packaging

C = Individual

C

Note: 

Refer to the QREV product code numbers and nominal capacities tables in the 

Quick Response

Expansion Valve (QREV) and Precision Superheat Controller (PSHC) Product Bulletin (LIT-12012398)

 to

determine the QREV capacity that you require.
Contact your Johnson Controls account representative about availability of 12 VDC QREV models.

Table 2 explains the naming convention for the PSHC model numbers, using the example code

PSHC01-134A-C.

Quick Response Expansion Valve and Precision Superheat Controller Installation Guide

2

Содержание PSHC Series



















Отзывы: