Pelsue 500714-001 Скачать руководство пользователя страница 13

Страница: 13 / 24

500714-001 - Product Manual - #FT-C70 Carbon Fiber Fall Arrest Tower - Revision 02 - 2015-03-06

Page 13

The Pelsue #FT-C70 Composite Fall Arrest Tower is constructed of a composite carbon fiber tube and base struc

ture composed of an aluminum & magnesium alloy, and also incorporates several alloy steel and engineered plas-

tic components. The Model #FT-C70 possesses a composite upper section (#500573-001) which can be inserted

into its standard base (#500019-001) to create a 70” high anchor point. The #FT-C70 can also be configured in a

“Rescue Mode” in the event a person or persons require rescue capabilities. In this configuration the tower can be

“heeled” over up to 23 degrees via the adjusting screw pegs in the base. This practice allows greater clearance away

from the side of the work platform for raising or lowering a fallen worker. The #FT-C70 tower can not be used for the

anchorage of fall arrest systems while configured in “Rescue Mode.” All specifications, instructions, and procedures

provided within this manual or upon Pelsue Specification Documents are based upon and only valid for usage with a

Pelsue FT series Fall Arrest Tower approved accessories. The T.A. Pelsue Company can not verify equipment safety

and/or compliance when utilized with anything other than Pelsue approved FT-C70 Series accessories.

Composite Fall Arrest Tower, Model #FT-C70

General Specifications

• Safe Working Radius @ Tower Base

5’10”

• Structure Weight

Tower - 10.5 lbs.

Base Assembly - 28.5 lbs.

• Tower Height

5’10”

5.0 - Product Operation

The following section will address the capabilities and the general operation of the Pelsue #FT-C70 Composite Fall Arrest

Tower. The instructions contained within this section should be adhered to each and every time the product is used. Any

person tasked with installing or operating this piece of equipment should be familiar with these procedures.

The load rating(s) reported within this docu-

ment may supersede or be superseded by

the rating of an accessory or complemen-

tary component. The capabilities of a com-

plete Personal Fall Arrest System (PFAS)

are limited by the “weakest” component

utilized within that complete system!

5.1 - Product Description & Capabilities

Load Capacity

• Up to three users with a maximum

weight of

310 lb/person

with a safe

working radius of

5’10”

about the

Tower Base

• Refer to loading diagrams for proof

loads.

Materials & Construction

Tower Assembly: Carbon Fiber,

Machined 6000 Series Alumi-

num, High-Tensile Nylon Web-

bing & High Strength Steel

Base Assembly: Aluminum &

Magnesium Alloy, Alloy Steel &

UHMW PE Components

Hardware: Plated Steel

Features:

• Installs on elevated surfaces where access is required via a

variety of available base option.

• Provides an elevated, swiveling fall arrest anchor point for up

to three persons

• Offers a “rescue mode” in the event that a person were to fall

and require rescue

Содержание 500714-001

























Результаты поиска

Содержание 500714-001

Отзывы:

Похожие инструкции для 500714-001

Бренды по названию

Популярные бренды

Pelsue 500714-001, Руководство по эксплуатации продукта

Результаты поиска

Содержание 500714-001

Отзывы:

Похожие инструкции для 500714-001

Бренды по названию

Популярные бренды