PELLET PRO 627 Скачать руководство пользователя страница 9

11 

 

 

SECTION FOUR: MAINTAINING 

YOUR NEW PELLET PRO

® 

GRILL

 

1.  Change the aluminum foil on the Grease Drain Pan frequently.  Periodically clean 

the grease out of the V-shaped Grease Drain and Grease Drain Tube and off of the 
interior surfaces of the Grill.  Empty the Grease Bucket occasionally and line with 
aluminum foil for easy clean-up.  It is easier to clean off accumulated grease when 
the Grill is warm.  

Be careful not to burn yourself.  

If too much grease is allowed to 

build up on the Grease Drain Pan and the V-shaped Grease Drain, or is allowed to 
plug the Grease Drain Tube, a grease fire could result.  We recommend cleaning 
these locations regularly.

 

2.  Outside surfaces: 

DO NOT 

use oven cleaner, abrasive cleansers or abrasive 

cleaning pads on the outside Grill surfaces.  Use warm soapy water to cut the 
grease.

 

3.  If the Grill is stored outside during the rainy season, care should be taken to ensure 

that water does not get into the Pellet Hopper.  Wood pellets, when wet, expand 
greatly and will jam your Auger.

 

4.  Depending on use, periodically remove the Porcelain Grill, Grease Drain Pan, and 

Heat Baffle to clean the ash from in and around the Firepot.  A shop-vac is handy for 
this chore.  Make sure the Grill is COLD before starting this procedure.

 

5.  We recommend keeping a long-handled cleaning brush near the Grill.  After 

removing your food, give the Porcelain Grill a quick brushing.  I takes only a minute 
and it will be ready the next time you want to use the Grill.  

Be careful not to burn 

yourself.

 

 

 

NOTE:

 

1)  The electric power supply cord should be replaced by a special line or 

personal module available from the manufacturer or its maintenance 
department when it is damaged.

 

2)  The equipment should be placed on a smooth either indoors or outdoors with 

inclination not more than 15 degrees.

 

3)  Children should be supervised to make sure they won't run into equipment.

 

4)  The equipment will not be available to the following persons (including 

children): person who has a physical or mental problem or lack of experience 
and the knowledge.  Unless they get supervision or guidance about the usage 
of this product from their guarders.

 

 

“WHO’S YOUR SMOKE DADDY?”

 

Pellet Pro

® 

Grill

 

www.pelletprogrill.com

 

Содержание 627










Отзывы: