background image

SOIL CULTIVATOR CULTIVION ALPHA

58_163161-A

 

1. INTRODUCTION

Dear Customer,

Thank you for purchasing your Soil Cultivator Cultivion Alpha. Properly used and maintained, this equipment will

give you years of satisfaction.

Warning

Your machine contains numerous recoverable or recyclable materials. Return it to

your dealer or, failing this, to an approved servicing centre to be treated.

Comply with the regulations in force in your country as concerns environmental protection associated with your

activity.

Warning

It is imperative that you read through the ENTIRE user’s manual guide before using or servicing

the tool. Always comply with the instructions and illustrations provided in the user’s manual.

Throughout the user’s manual guide you will find advisory notes and information entitled: NOTE, IMPORTANT,

ATTENTION and WARNING.

Points marked “NOTE” indicate additional information.

Points marked "IMPORTANT" warn the user of a potential risk for the equipment.

Points marked “ATTENTION” warn the user of a potentially hazardous situations which if not avoided may result

in minor injuries.

Points marked “WARNING” warn the user of a potentially hazardous situation which if not avoided may result in

serious injury or death.

The warning 

 indicates that damage resulting from failure to comply with the procedures and instructions is not

covered by the warranty and the owner will be liable for any repair costs.

Safety indications are also given on the tool; they remind you of the safety precautions to be taken. Identify and

read these indications before using the tool. Immediately replace any indications that may become partially illegible

or deteriorated.

Refer to Section 2.5, “Safety signage” for the location diagram of the safety stickers affixed to the tool.

No part of this manual may be reproduced without the written permission of the company PELLENC. The illustrations

provided in this manual are for information purposes only and are in no way contractual. The PELLENC company

reserves the right to make any modification or improvement to its products as deemed necessary without inform-

ing customers already in possession of a similar model. This manual forms an integral part of the tool and must

accompany the tool if it changes hands.

5

Содержание 58W00001

















































Отзывы: