background image

E. 

Plumb and square window. 

0LACESHIMS

from the bottom and top of the window between 
the window and the sides of the opening. Adjust 
the shims as required to plumb and square the 
window in the opening. If the frame height 

EXCEEDSPLACESHIMSATTHEMIDPOINT

of the window sides.

Note: DO NOT shim above the 
window or in the space between 
the spacers at the bottom of the 
window. DO NOT over shim.

Ó

£

Ó ä Î ä

{ ä x ä

È ä Ç ä

Ó

Î

 -

““

Ó

Ó

Ó

'JYFE

&YUSVEFE'JO

F. 

Check the interior reveal. 

Make sure the 

measurement from the interior face of the 
window to the interior face of the wall is 
equal at several points around the window.

Note: If the dimensions are not equal, 
check to make sure the fins are folded out 
to 90˚ at all points.

'

Fasten the window to opening. 

/NWINDOWSWITHAlXED

EXTRUDEDlNDRILLDIAMETERHOLESINTHElNEVERY

A. 

Units that do not have pre-applied fin corners:

#UTFOURPIECESOFmASHINGTAPELONG

!PPLYONEPIECEOFmASHINGTAPETOEACHENDOFTHESILLlNSOTHATITEXTENDSPASTTHE
ENDOFTHESILLlN!PPLYONEPIECEOF

flashing tape to the bottom end of 

EACHmEXIBLElNBEGINNING
FROMTHEENDOFTHElNANDLAPPING
OVERTHEmASHINGTAPETHATEXTENDS
FROMTHEENDOFTHESILLlN

3

INTEGRATING THE WINDOW TO 

THE WATER RESISTIVE BARRIER

Î

TU

Î

OE

(

Drive a 2" galvanized roofing nail

 into each of the pre-punched and pre-drilled holes.

 

For flexible fin:

$RIVENAILSUNTILTHEHEADCONTACTSTHElNHOWEVERDONOTSINKTHEHEAD

This allows for movement of building materials.

Note: Make sure all fin corners are lying as flat as possible.

Содержание 801U0102









Отзывы: