pela tools 63045, Руководство пользователя

Страница: 7 / 12

Contact
PELA Tools
Solängsvägen 13
SE-513 70 Borås
Phone: 033-202650
E-mail: order@pelatools.com
Environmental protection /
Scrapping
Recycle any unwanted material,
do not throw it in the household
rubbish. All machines, accessories
and packaging must be sorted and
left at a recycling center and disposed
of in an environmentally friendly manner.
1.
Specifications
Connection.............................. 230 V/50 Hz, 1240 W
Max. working pressure................................... 8,6 bar
Air consumption................ca 400-600 liters/minute
Compressed air connection............................... 1/2”
External dimensions.............1350 x 900 x 1700 mm
Internal dimensions................1210 x 600 x 580 mm
Weight...............................................................157 kg
Visible glass.........................................570 x 270 mm
Complete with lamp, gloves and protective film.
Important!
Carefully read the safety instructions and
installation instructions before using the product.
This way you get the most out of your device and
accidents can be avoided. Save the operating
instructions for future use. In the event of a sale,
the instructions must accompany the cabinet.
SAFETY INSTRUCTIONS
Carefully read the manuals safety instructions
before using the blasting cabinet. WARNING! When
using the blast cabinet, basic precautions must
always be followed to reduce the risk of personal
injury and other risks caused by excessive air
pressure.
1. Connecting compressed air hoses should not
have a dimension smaller than 8 mm and must
withstand a pressure of at least 8.6 bar. Always
disconnect the plug from the wall socket and
disconnect the compressed air hose when the
blasting cabinet is not in use. And when filling
with blast media, when servicing all kinds of
accessories and when changing accessories.
2. The compressed air must be free of
contaminants such as oil, moisture, etc. Do not
use the blasting cabinet in damp, wet or poorly
lit workplaces. Do not expose the blast
cabinet to rain. Keep the work surface well lit
and clean. Dirty workplaces involve a greater
risk of accidents.
3. Only connect to a grounded 230 V / 50 Hz
electrical outlet.
4. Wear safety goggles and hearing protection.
5. Always wear approved safety goggles when
using the blasting cabinet. NOTE! Ordinary
glasses are not goggles. Use hearing protection
as the noise level of the blower cabinet may be
high during use. Use only recommended blas -
ting materials. Always replace a broken protec -
tive glass with one of the same size and quality.
6. Keep children away from equipment. Children
are not allowed to stay near the blast cabinet.
Never let them handle the blast cabinet or its
accessories.
7. When the blast cabinet is not in use, it must
be stored in a dry place to protect against rust,
and in a locked space so that it is stored out of
reach of children.
8. Replace the gloves. Protective gloves wear,
replace them with new ones when required.
9. Close and lock the door during use.
10. Be careful of the adapter. Never disconnect the
adapter from the wall outlet with wet hands.
Keep the power cord away from heat, oil and
sharp edges.
Assembly instructions
1. Remove all parts from the inside of the
cabinet together with the grid from the bottom of
the drawer, under the packaging..
2. Place the cabinet upside down and mount the
legs, use M6 x 12 mm screw. The front legs are
marked. Fit cross braces between back legs and
front legs.
3.Set up the cabinet on the legs and mount the
regulator (9) on the left front leg with M6x 12 mm
screw and nut.
4. Place the foot pedal between the front legs.
5. Attach the metering valve (13), use three screws
to attach the hinge to the back of the cabinet.
Finish by closing the door lock.
6. Install the right and left doors with screws and
nuts located on the hinge. Install sealing strip.
Install the plate for the door locks on each side.
Adjust sideways so that the door seals just enough.
7. Place the lamp glass on the gasket with the
screen protector facing down on top of the blast
cabinet. Mount the lamp and then fasten it in place.
8. Use 4 M6 x 12 mm screw and flange nut to
mount the vacuum cleaner. Loosen the suction
cover on the inside and seal around the connecting
pipe. Mount the shaker function from inside the