pela tools 53393, Инструкция по эксплуатации

Страница: 5 / 8

Instructions
Warning : The warnings and instructions discussed
in this manual may not cover all possible condi-
tions and situations that may arise. It must be un-
derstood by the operator that common sense and
caution are factors that can not be built into this
product but must be provided by the operator.
Warning
Do not exceed the maximum capacity of 450 kg.
1.
Always use the stand on a hard, flat surface
that can maintain the load.
2.
Never work directly under a suspended engine.
3.
Do not attempt to move the stand when it is
under load. The wheels are not designed for
rolling when the stand carries a heavy weight. If
you need to move the engine, you must transfer
it to an approved, suitable mobile device, e.g. a
motor lift.
4.
Make sure the stand is stable. Before using the
stand, check it for cracks, bends in the metal
or signs of unusual wear. If there are any, do
not use the stand. Contact Verktygsboden for
service or repair.
5.
Do not attempt to remove an engine from a
vehicle using this unit. Use a motor lift (not
included). Read all safety warnings and instruc-
tions that come with the engine lift.
6.
Be careful not to pinch your fingers and hands
when adjusting and using the motor stand.
7.
Make sure that the load is centered and fixed
on the mounting plate.
8.
Do not release suddenly as it may damage the
device.
9.
Make sure that all nuts and bolts are properly
mounted and tightened before each use. Do not
replace the hardware provided.
10.
WARNING: Failure to follow these instructions
could result in loss of cargo and / or personal
injury or property damage.
Inspection
1.
Visual inspection should be performed before
each use of the motor stand.
2.
Any motor stand that appears to be damaged in
any way, turns out to be worn or does not work
normally must be taken out of service.
3.
If the motor stand is accidentally subjected to
an abnormal load or shock, it must be inspec-
ted by a qualified technician immediately.
4.
It is recommended that an annual inspection of
the engine stand be performed and that defecti-
ve parts / decals or warning labels be replaced.
Assembly instructions
Warning : During the assembly procedure, nuts and
bolts should only be tightened by hand. When the
assembly is complete, nuts and bolts must be tigh-
tened completely.
1. Attach two front wheels (# 19) to the front
beam (# 20) with nuts (# 17) and lock was-
hers (# 18).
2. Attach the front beam (# 20) to the center
beam (# 16) using bolts (# 9), nuts (# 11)
and lock washers (# 10).
3. Attach the main post (# 5) to the rear beam
(# 14) using bolts (# 9), nuts (# 11) and
lock washers (# 10) ..,
4. Insert the middle beam (# 16) on the main
post pipe (# 5) and secure it with a bolt (#
15).
5. Insert the rotating plate (# 3) through the
tube at the top of the main post. Rotate
the plate until one of the holes in the inner
tube aligns with a hole in the outer tube and
insert the ringed pin (# 4).
6. Insert the handle (# 1) through the hole in
the rotating plate tube protruding from the
top of the main post.
7. Attach four pins (# 2) to the rotating head
(# 3) using bolts (# 8), flat washers (# 6)
and nuts (# 7).
8. Make sure all bolts are tightened before
using it.
Contact
PELA Tools
Solängsvägen 13
SE-513 70 Borås
Phone: 033-202650
E-mail: order@pelatools.com
Environmental protection /
Scrapping
Recycle any unwanted material,
do not throw it in the household
rubbish. All machines, accessories
and packaging must be sorted and left
at a recycling center and disposed
of in an environmentally friendly
manner.
5