background image

2 of 22

2016-09-07   SHEET #: 180-9091-1

Note:

 Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List............................................................................................................................................................................. 3, 4

Enclosure Wall installation ...................................................................................................................................................... 5

Enclosure Installation to ESA763PU Articulating Wall Mount ................................................................................................. 7

Enclosure Installation to EPT650 Tilt Wall Mount ................................................................................................................. 16

Wireless Receiver Setup ...................................................................................................................................................... 18

Tools Needed for Assembly

• stud fi nder ("edge to edge" stud fi nder is recommended)

• phillips screwdriver

• drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

•  level

•  7/16" open end wrench

•  5mm allen wrench

•  6mm allen wrench

•  Do not begin to install your Peerless product until you have read and understood the instructions and warnings 

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US 
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact 
your local distributor.

•  This product should only be installed by someone of good mechanical aptitude, has experience with basic building 

construction, and fully understands these instructions.

•  Due to outdoor environmental conditions such as heavy snow, hail, rain, etc. the environmental mount and 

hardware must be inspected at least once a year. This product should not be exposed to high winds. A qualifi ed 
installer or inspector must check for signs of rust, loose fasteners, bent metal, etc. If evidence of excessive wear, 
deterioration or any unsafe condition is observed, this product must be taken out of service immediately. Direct all 
inquiries to customer care if you have any questions.

•  Make sure that the supporting surface will safely support the combined load of the equipment and all attached 

hardware and components.

•  Never exceed the Maximum Load Capacity. See page one.

•  If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of 

an "edge to edge" stud fi nder is highly recommended.

•  Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding 

power.

•  This product was designed to be installed on the following wall construction only;

 

WALL CONSTRUCTION 

 

HARDWARE REQUIRED

 • 

 

Wood 

Stud   Included

 

  Wood Beam 

 

 

Included

 

  Solid Concrete 

 

 

Included

 

  Cinder Block 

 

 

Included

 

•  

Metal 

Stud   Contact 

Qualifi ed Professional

 

•  

Brick 

   Contact 

Qualifi ed Professional

 

•  

Other or unsure?   

 

Contact Qualifi ed Professional

 WARNING

Содержание HDS-OWK Series























Отзывы: