6
Input Panel
(1) XLR Mic Input (Ch 1&2)
Use this XLR connector to connect a microphone to the P1/2/3BT speaker.
(2) Line Input (Ch 1&2)
Use this 1/4" (6.5mm) connector to connect a line-level source to the P1/2/3BT speaker. The line input is typi-
cally used for sources like keyboards and CD players.
(3) RCA and 3.5mm Input (Ch 3)
These inputs, RCA and 3.5mm (1/8") accept a stereo input from the output of an MP3 player, CD player, phone
or similar device.
(4) 3.5mm/RCA Input Selector (Ch 3)
This switch selects the source being sent to channel 3. In the upper position, the RCA inputs are sent to channel
3. In the lower position, the 3.5mm (1/8") connector is sent to channel 3.
(5) Level Control
Use this to adjust the source level in the corresponding channel.
(6) Low EQ (Bass)
This is an active tone control (shelving type: +/-15dB) that varies the level of the low frequency range.
Caution:
Excessive low frequency boost causes greater power consumption and increases the possibility of
speaker damage.
(7) High EQ (Treble)
This is an active tone control (shelving type: +/-15dB) that varies the level of the high frequency range.
(8) Master Volume
The master volume control adjusts the overall level of the speaker.
(9)Power LED
LED illuminates when power has been applied to the speaker.
(10) Sync XLR In/Out
The sync XLR In/Out connectors are used to daisy chain multiple speakers. Using these inputs, the signal source
can be fed to multiple speakers, while allowing the level of each speaker to be set by its own master volume con-
trol independent from the other speakers in the chain.
(11) Subwoofer Out
This 1/4" jack can be used to drive an external subwoofer amplifier or a power sub. The signal level is pre-master
volume control. This allows the user to balance the signal between the speaker and the subwoofer.
P1 BT
SYNC
IN
OUT
Subwoofer Out
PAIRING
STEREO LINK
AC 100-240Vac 50-60Hz
POWER
POWER
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN-ICES-3(B)/NMB-3(B)
WARNING:
This speaker system can permanently damage hearing!
Use extreme care setting maximum loudness!
AVERTISSEMENT:
Ce système de haut-parleurs peut définitivement endommager l'ouïe!
Soyez extrêmement prudent en réglant le volume maximum!
Consumo de energia 180Wh
P1 BT
Electronics Corp.
Peavey
FCC ID: I4S-PBT
IC: 3642A-PBT
Bluetooth Pairing
1. Press mode button to enter the BT pairing mode.
2. Connect your Bluetooth device to P1 BT.
Stereo Linking Two Speakers
1. Pair your Bluetooth device to first speaker.
2. Press Pairing on the second speaker to turn BT on.
3. Press Stereo Link on both speakers under BT Mode.
4. To disconnect ,press the Stereo Link button again
on either speaker.
While Pairing or Linking LEDs will flash.
When Paired or Linked LEDs will be solid.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
THIS APPARATUS SHOULD NOT BE EXPOSED TO RAIN OR MOISTURE
AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT
BE PLACED ON THIS APPARATUS. TO PREVENT THE RISK OF FIRE
HAZARD, REPLACE WITH SAME TYPE 250 VOLT FUSE
CAUTION
AVIS:
DANS LE BUT DE REDUIRE LES RISQUES D’INCENDIE OU DE
DECHARGE ELECTRIQUE, CET APPAREIL NE DOIT PAS ETRE EXPOSE
A LA PLUIE OU A L’HUMIDITE ET AUCUN OBJET REMPLI DE LIQUIDE,
TEL QU’UN VAS, NE DOIT ETRE POSE SUR CELUI-CI. REMPLACER
PAR UN FUSIBLE DE MEME TYPE ET DE 250 VOLTS.
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
100-240V
F2.5AL/250V
10
11
9