How to use your laminator
1) Carefully remove the laminator from all of its packaging and place it on a flat, level surface. Make sure you
keep the original packaging somewhere safe (in case this is needed in the future).
2) Unpack the power cable and insert it into the power outlet at the back of laminator. Plug it in to a power socket.
Press the Red POWER switch to turn the laminator on. The power light will illuminate.
3) Set the HEATER switch to ON.
4) Check that the FWD/REV (Forward and Reverse) switch is set to FWD (See diagram 1)
5) Refer to the temperature chart and set the laminator to the required temperature.
6) The laminator will now begin to heat. Once it has reached the set temperature, the green READY light will illuminate.
7) Place the document you are laminating inside the pouch, making sure that it is centrally positioned and that a small
border (approx 5mm) is left around the edge. If you are laminating cut-up pieces then you need to use a Lifejacket®.
If you do not have one of these, ask your supplier.
8) Once the document (or small pieces) are positioned in the pouch (and are not overlapping or touching each other),
insert the prepared document into the laminator. Make sure you insert the SEALED EDGE FIRST and do not insert
at an angle. The item will automatically feed through and appear the other end.
!
Do not tug or pull the document as it comes out of the back of the laminator.
9) To turn off the laminator after use, set the HEATER switch to OFF and allow the laminator to still run for 5 minutes
(you will hear the rollers turning). This allows the laminator to cool down and it is then safe to turn the
POWER switch OFF after this time.
It is important that you watch your document as you laminate in case of jamming. If your laminating appears to be
jamming, press the REVERSE switch and gently ease the document back out.
Temperature control
Laminating pouch thickness
Paper Type
Approx temperature (
o
C)
150 to 200 micron total
(75 + 75 per side up to 100 + 100
per side)
Copy paper (80gsm)
110-120
Photo paper (120gsm)
115-120
Card (200gsm)
115-125
250 to 360 micron total
(125 + 125 per side up to 180 + 180
per side)
Copy paper (80gsm)
120-125
Photo paper (120gsm)
125-130
Card (200gsm)
125-130
360 micron (maximum)
(180 + 180 per side)
Copy paper (80gsm)
130-140
Photo paper (120gsm)
135-140
Card (200gsm)
135-145
Ready light
Power switch
Temperature
control knob
Forward/Reverse
switch
Heater/Cold
switch
Laminating speed:
560mm/minute
Laminating width:
320mm
Maximum pouch thickness: 360 micron
Laminating temperature:
100-160
o
C
Warm up time:
5 minutes
Power supply:
AC 100, 110, 220
240V/50Hz, 60Hz
Power consumption:
450W
Dimensions:
535 x 215 x 113mm
Weight:
8.8kgs
Warranty:
2 years
Technical Specifications
Parts and Features
Diagram 1
Temperature control is designed for laminating pouches and documents of varying thickness. Thicker objects
need more heat. The table below gives an indication of the correct temperature setting required.
Please note
this is a guide only. Other factors can affect the laminator such as room temperature and the thickness of
document being laminated.
Thank you for purchasing the Peak Pro PP330. Peak laminators are designed to give you professional,
high quality results, quickly and easily. Please take a few minutes to read through this important document as
any
damage caused to your laminator by user error is not covered under warranty.
x
x
Don’t overlap
Leave a 5mm border
Don’t laminate open
end first
Never laminate without
using a Lifejacket® or you
risk jamming and damaging
your laminator (this will not
be covered under warranty)
x
What is a ‘Lifejacket®’?
The Lifejacket® is a highly durable patented product made from teflon® that should be used when laminating
cut-up, odd shaped pieces (such as shapes, letters, signs as show above) to prevent damage to your laminator
and potential jamming. Why use a Lifejacket®?
. Protect your laminator from jamming
. Extend the life of your laminator by using the Lifejacket® - stops adhesive seeping onto the rollers
. Eliminate repair bills as this product keeps your laminator working at an optimum level
. Available in A4, A3 and A2 sizes to protect documents of all sizes
Ask your supplier for more details.
