manualshive.com logo in svg

Peak OEM 32, Руководство по установке, Страница: 25 / 27

Поделиться
Скачать
Peak OEM 32 Скачать руководство пользователя страница 25

PEAK® OEM 32 24 Volt SMART Equipment Controller Installation Instructions

25

Terminations

Input/Output: Fixed spade terminals
SA/FC/Modbus: 4-Wire and 3-Wire pluggable screw terminal blocks
SA bus tool port: RJ-12 6-Pin modular jack

Field install option:

Input/Output: Fixed solder terminals
SA/FC/Modbus: 4-Wire and 3-Wire pluggable screw terminal blocks
SA bus tool port: RJ-12 6-Pin modular jack
See Table 7 for number of cycles and electrical ratings

Mounting

Horizontal on single 35 mm DIN rail mount (preferred), or screw mount on flat surface with 

three integral mounting clips on controller.
Mount the PEAK OEM 32 controllers on a wall or DIN rail inside an enclosure rated at least 

IP20. 

Housing

Enclosure material: Polycarbonate LEXAN

®

 SABIC EXL9330

Dimensions
(H x W x D)

220 mm x 125 mm x 58 mm (8.66 in. x 4.92 in. x 2.28 in.)

Weight

0.5 kg (1.1 lb)

Compliance

United States:

 UL Listed, File E107041, CCN PAZX, UL 916, Energy Management

Equipment
FCC Compliant to CRF47, Part 15, Subpart B, Class A

Canada:

 UL Listed, File E107041, CNN PAZX7 CAN/CSA C22.2 No.205, Signal Equipment

Industry Canada Compliant, ICES-003

Europe:

 Johnson Controls declares that this product is also in compliance with the essential 

requirements and other relevant provisions of the EMC Directive and Declared as Electronic 

Independently mounted control, suitable for DIN rain mounting. Intended to mount in remote 

panel. Type 1.C (Micro-interruption), 330 V rated impulse voltage. 125°C ball pressure test.

Australia and New Zealand: 

RCM Mark,

 

Australia/NZ Emissions Compliant

BACnet International: 

BACnet Testing Laboratories (BTL) Protocol Revision 12 Listed 

BACnet Advanced Application Controller (B-AAC)

PK-OEM32x0-0 (Part 2 of 2 )

Содержание OEM 32




























Отзывы:

Нет отзывов