background image

Page

Fuze Part # 4532 - Patent Pending 

 May 2007

May 2007

Fuze Part # 4532 - Patent Pending

Page

Page

Fuze Part # 4532 - Patent Pending 

 May 2007

 January 2014

 

Fuze Part # 4532 - Patent Pending 

Page

Use this information only as a basic guide. The techniques that are discussed 

on the following pages have been used successfully by many.
Individual wheelchair users often develop skills to deal with daily living 

activities that may differ from those described in this manual. PDG recog-

nizes and encourages each individual to try what works best for him/her in 

overcoming architectural obstacles that they may encounter, however ALL 

WARNINGS and CAUTIONS given in this manual MUST be followed. 

Techniques in this manual are a starting point for the new wheelchair user 

and assistant with “safety” as the most important consideration for all.

G. Note to Wheelchair Assistants

 

æ

WARNING

æ

1. When assistance to the wheelchair user is required, remember to use good

body mechanics. Keep your back straight and bend your knees whenever 

tipping the wheelchair or traversing curbs, or other impediments.

2. DO NOT attempt to lift the wheelchair by any removable (detachable)

parts. Lifting by means of any removable (detachable) parts of a wheel-

chair may result in injury to the user or damage to the wheelchair.

3. DO NOT use the spreader bar for lifting or transporting the wheelchair.
4. DO NOT use the spreader bar as a weight bearing support. When learning

a new assistance technique, have an experienced assistant help you before

attempting it alone.

H.  Tilting the Wheelchair

 

æ

WARNING

æ

1. DO NOT tilt the wheelchair without assistance
2. When tilting the wheelchair, an assistant should grasp the back of the

wheelchair on a non-removable (non-detachable) part. Inform the wheel-

chair occupant before tilting the wheelchair and remind him/her to lean

back. Be sure the occupant’s feet and hands are clear of all wheels.

3. After mastering the techniques of tilting the wheelchair, use this procedure

to tackle shallow curbs, short stairs, etc.

I.  Curbs and Steps

æ

WARNING

æ

1. Each person who helps you should read the “Notes to Wheelchair

Assistants” (Section G above).

11

Содержание Fuze T20





































Отзывы: