Model Number
260A 02
3-COMPONENT ICP® FORCE SENSOR
Revision: E
ECN #: 50553
P erfo rm an ce
EN G L ISH
SI
Sensitivity(± 20 %)(Z Axis)
2.5 mV/lb
0.56 mV/N
[1][2]
Sensitivity
(± 20 %)(X or Y Axis)
5 mV/lb
1.12 mV/N
[1][2]
Measurement Range(Z Axis)
1,000 lb
4.45 kN
Measurement Range
(X or Y Axis)
1,000 lb
4.45 kN
Maximum Force(z axis)
1,320 lb
5.87 kN
Maximum Force
(x or y axis)
1,000 lb
4.45 kN
Maximum Moment(z axis)
40 ft-lb
54.23 Nm
Maximum Moment
(x or y axis)
70 ft-lb
94.91 Nm
Broadband Resolution(z axis)
0.006 lb-rms
0.027 N-rms
[3]
Broadband Resolution
(x or y axis)
0.006 lb-rms
0.027 N-rms
[3]
Upper Frequency Limit
90 kHz
90 kHz
Low Frequency Response(- 5 %)(z-axis)
0.01 Hz
0.01 Hz
Low Frequency Response
(- 5 %)(x or y axis)
0.001 Hz
0.001 Hz
Non-Linearity
≤ 1 % FS
≤ 1 % FS
[4]
Cross Talk(between x and y axis)
± 3 %
± 3 %
Cross Talk
(between (x or y axis) and z axis)
± 5 %
± 5 %
En viro n m en tal
Temperature Range
-65 to +250 °F
-54 to +121 °C
Electrical
Full Scale Output(Z Direction)
± 2.5 VDC
± 2.5 VDC
Full Scale Output
(X and Y Direction)
± 5 VDC
± 5 VDC
Discharge Time Constant(z axis)
≥ 50 sec
≥ 50 sec
Discharge Time Constant
(x or y axis)
≥ 500 sec
≥ 500 sec
Excitation Voltage(all channels)
20 to 30 VDC
20 to 30 VDC
Constant Current Excitation(all channels)
2 to 20 mA
2 to 20 mA
Output Impedance
≤ 100 Ohm
≤ 100 Ohm
Output Bias Voltage
8 to 14 VDC
8 to 14 VDC
Output Polarity
Positive
Positive
P h ysical
Preload
10,000 lb
44.48 kN
[5]
Stiffness(z axis)
19 lb/µin
3.3 kN/µm
[3]
Stiffness
(x or y axis)
6 lb/µin
1 kN/µm
[3]
Size (Height x Length x Width x Bolt Diameter
x ID x Sensing Surface)
0.390 in x 1.35 in x 1.25 in x 0.512
in x 0.512 in x 0.920 in
9.90 mm x 34.3 mm x 31.8 mm x
13 mm x 13 mm x 23.37 mm
Weight
1.59 oz
45 gm
Housing Material
Stainless Steel
Stainless Steel
Sealing
Hermetic
Hermetic
Electrical Connector
4-Pin
4-Pin
Electrical Connection Position
Side
Side
[6]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Piezotronics, Inc.
W
- Water Resistant Cable
Electrical Connection Position
Side
Side
OP TION A L VERSION S
Optional versions have identical specifications and accessories as listed for the standard model except
where noted below. More than one option may be used.
N OTES:
[1]Sensitivites are for listed preload. Sensitivites may vary ±5% depending on preload used.
[2]Sensitivities are dependent upon supplied bolt.
[3]Typical.
[4]Zero-based, least-squares, straight line method.
[5]Preload should be at least 10 times the X and Y operating range used.
[6]See PCB Declaration of Conformance PS023 for details.
Date: 04/17/2020
Date: 04/17/2020
Date: 04/17/2020
Date: 04/17/2020
12719
Entered: LK
Engineer: RPF
Sales: KK
Approved: RPF
Spec Number:
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: [email protected]
SU P P L IED A C C ESSORIES:
Model 081A74 Pre-load bolt (for Models 260A02, 260A12, and 260A32) (1)
Model 082M12 Anti-friction washer (for Models 260A02, 260A12, and 260A32) (1)
Model 083A13 Pilot bushing (for Models 260A02, 260A12, and 260A32) (1)
Model M081A74 Mounting Stud (1)
