manualshive.com logo in svg

PCB Piezotronics Larson Davis SoundAdvisor NMS044, Справочное руководство

Поделиться
Скачать
PCB Piezotronics Larson Davis SoundAdvisor NMS044 Скачать руководство пользователя страница 41

NMS044 Reference Manual

System LED Indications

A-3

A.1.2 LED Indicators for RV50X Cellular Gateway

When installed and running, the state of the gateway is indicated by the 4 LEDs on the side

and bottom of the device. Individual lighted LEDs and combination lighted LED indications

are listed in 

Table A.3

:

Table A.3  

Gateway LED Indications

LED

Color/Pattern

Description

Power

Off

No power or input voltage > 36 Vdc or < 7 Vdc

Solid Green

Power is present

Green with Amber Flash

Power is present and the gateway has a GPS fix

Solid Red

Standby mode

Flashing Green

When you press the reset button, flashing green indicates when to 

release the reset button to reboot the gateway.

Flashing Red

When you press the reset button, flashing red indicates when to 

release the reset button to reset the gateway to the factory default 

settings.

Signal

Solid Green

Good signal (equivalent to 4-5 bars)

Solid Amber

Fair signal (equivalent to 2-3 bars)

Flashing Amber

Poor signal (equivalent to 1 bar)

If possible, move the gateway to a location with a better signal.

Flashing Red

Inadequate (equivalent to 0 bars)

If possible, move the gateway to a location with a better signal

Network

Solid Green

Connected to an LTE network

Solid Amber

Connected to a 3G or 2G network

Flashing Green

Connecting to a network

Flashing Red

No network available

Flashing Red/Amber

Network Operator Switching is enabled, but the gateway is unable to 

locate the required firmware. For more information, contact Sierra 

Wireless®.

Activity

Flashing Green

Traffic is being transmitted or received over the WAN interface.

Flashing Red

Traffic is being transmitted or received over the serial port. This 

behavior only appears if the RV50X is configured to display it. For 

more information, contact Sierra Wireless®.

Flashing Amber

Traffic is being transmitted or received over both the WAN interface 

and the serial port. This behavior only appears if the RV50X is 

configured to display it. For more information, contact Sierra 

Wireless®.

ALL

Green LED chase

Radio module reconfiguration/firmware update or Network Operator 

Switching is in progress.

Amber LED chase

ALEOS software update is in progress.

Содержание Larson Davis SoundAdvisor NMS044




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды