PCB Piezotronics ICP 103B11, Инструкция по установке и эксплуатации, Страница: 9 / 10

Model Number
103B11
ACOUSTIC ICP® PRESSURE SENSOR
Revision: C
ECN #: 49341
Performance ENGLISH SI
Measurement Range(± 5 V output) 10 psi 190.7 dB
Useful Overrange(± 10 V output) 20 psi 196.7 dB
[1]
Sensitivity(± 15 %) 500 mV/psi 72.5 mV/kPa
Maximum Pressure 250 psi 1724 kPa
Resolution 0.06 mpsi 86.3 dB
Resonant Frequency ≥ 13 kHz ≥ 13 kHz
Rise Time ≤ 25 µ sec ≤ 25 µ sec
Low Frequency Response(-5 %) 5 Hz 5 Hz
Non-Linearity ≤ 2.0 % FS ≤ 2.0 % FS
[2]
Environmental
Acceleration Sensitivity ≤ 0.0005 psi/g ≤ 0.0035 kPa/(m/s²)
Temperature Range(Operating) -100 to 250 °F -73 to 121 °C
Temperature Coefficient of Sensitivity ≤ 0.2 %/°F ≤ 0.36 %/°C
Maximum Flash Temperature 1000 °F 538 °C
Maximum Shock 1000 g pk 9807 m/s² pk
Electrical
Output Polarity(Positive Pressure) Positive Positive
Discharge Time Constant(at room temp) ≥ 0.1 sec ≥ 0.1 sec
Excitation Voltage 20 to 30 VDC 20 to 30 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance ≤ 100 Ohm ≤ 100 Ohm
Output Bias Voltage 7 to 13 VDC 7 to 13 VDC
Physical
Sensing Element Ceramic Ceramic
Housing Material Stainless Steel Stainless Steel
Diaphragm 316L Stainless Steel 316L Stainless Steel
Sealing Epoxy Epoxy
Electrical Connector Integral Cable Integral Cable
Cable Termination Pigtail Ends Pigtail Ends
Weight 0.115 oz 3.260 gm
Cable Type 32 AWG stranded wires 32 AWG stranded wires
Cable Length 15 in 38.1 cm
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Group, Inc.
OPTIONAL VERSIONS
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
M
- Metric Mount
Supplied Accessory : Model M061A04 Clamp (2)
NOTES:
[1] For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may
be limited by output bias.
[2] Zero-based, least-squares, straight line method.
SUPPLIED ACCESSORIES:
Model 061A04 Sleeve clamp 4-40 cap screw (2)
Model 065A66 Adhesive Mounting Ring (3)
Model 070B09 Solder adaptor
Entered: LK Engineer: MJK Sales: KK Approved: RPF Spec Number:
Date: 3/29/2019 Date: 3/29/2019 Date: 3/29/2019 Date: 3/29/2019
24846
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com