PC MARKETING Tropical Series, Инструкция по уходу, использованию и установке

Страница: 8 / 20

8
•
Assembly of the Lift and Pedestal. (figure 2)
Set up the lift (29), and position the pedestal (30) centrally and flush in front of the lift. Now, working from
the inside of the pedestal, join the lift (29) and the pedestal (30) by screwing the four hexagon socket-head
screws (25) and washers (26) again.
•
Assembly of the pistons. (figure 7)
Both pistons must be installed when assembling your new tanning unit on site. Insert the pistons in the
stand before the canopy is mounted.
TROPICAL SERIES 41 U·P·P: 2 pistons with 950 N
TROPICAL SERIES 32 GB: 1 piston with 950 N
1 piston with 950 N
Hold the piston (figure 7) between the U-shaped part of the stand so that the fixing fork (2) of the piston
shows in the direction of the holder for the canopy (3). The piston must be assembled with the fat end
(body) down and the skinny end (shaft) up. (see figure 7)
All bolts must be lubricated
Take the shorter bolt (4) which is 23 mm long and put it through the fixing fork of the piston and through the
holder for the piston. Fasten the bolt by the two washers (5). Take the bolt of 46 mm lenght (6) and lead it
through the U-shaped part of the stand, through both spacers (7) and through the piston. Fasten also this
bolt by the 2 washers (5). Install the second piston the same way. Now the canopy can be assembled.
Push the lounge drawer (21) onto the upper guide rails, the canopy drawer (22) onto the middle guide rails
and the controls drawer (23) onto the lower guide rails.
The Unit with high pressure facial (GB) has only 2 drawers. The drawer with the operating
hour counter (34) is the controls drawer. Always slide this control drawer on the lower
guide rails. Join the connectors of the high pressure facial unit in same manner as the
low pressure unit U-P-P . All connectors are coded.
Pull the supply power cable (34) from the controls draer outwards over the clamping screw (35) and strain
relief clamp which is on the right front part of the pedestal. Leave enough cable in the right hand space of
the pedestal so that the controls drawer can still be pulled out. Connect the short cable socket (36) to the
plug on the clamp (37). Connect the lounge drawer connector (38) and the canopy drawer connector (39)
to the main drawer.
The connectors are marked 1-1 and 2-2. Join the same numbers together
Place the 29 pole socket (40) from the lounge drawer on the right in the insede of the pedestal. The socket
is connecting the lounge. ull the two 29 pole socket (47 and 48) from the canopy module (22) also into the
right of the pedestal open space.
•
Assembly of the Canopy (figure 1)
Lift the canopy with an assistant and hold it above the lift so that the head of the pan head screws (17) can
be inserted in the lift holders (14).
For safety, screw in the four hexagon head bolts (15) and washers (16) and be sure to
tighten them.
Guide the two large grey cables (43) between the two lift cross members (44), through the air intake hole
and along the pedestal rear wall to the right hand open space on the front of the pedestal. Connect the two
plugs (45 and 46) to the two control module sockets (47 and 48).
Fix the cover (13) with screws. Then mount the cover plate (41), the cover (9) with the inserts (12), screws
(11) and partially with the caps (10). Put the upper cover plate (8) back in place . guide this first into the slot
in the large cover (53), then press it further in this direction until it locks in the rear rail. Fix the cover (104)
again by screwing in the screws (105) and by tightening the screws (106). Fix the cover (45) from behind
with the inserts, screws and (in some cases) the covering caps.
The connectors are coded.
•
Assembly of the Lounge (figure 2)
Hold the base over the pedestal so that the centering (49) are in the front. Place the lounge on the pedestal
so that the centering pins slide into the holes (50) provided for them and the lounge cable falls into the right
hand pedestal space. Connect the lounge cable plug (42) to the lounge drawer socket (40). Secure the
lounge with nuts (24) and washers.