background image

person nearby, if so, pay attention to guard against theft. 

FCC compliance statement 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired operation. 

changes or modifications not expressly approved by the party responsible for compliance 
could void the user’s authority to operate the equipment. 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures: 
-- Reorient or relocate the receiving antenna. 
-- Increase the separation between the equipment and receiver. 
-- Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected. 
-- Consult the dealer or an experienced radio/TV technician for help. 

ISED compliance statement 
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, 
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to 
the following two conditions:   
(1) This device may not cause interference.   
(2) This device must accept any interference, including interference that may cause 
undesired operation of the device.   
L’émetteur/récepteur exempt de licencecontenu dans le présentappareilestconforme aux 
CNR d’Innovation, Sciences et Développementéconomique Canada applicables aux appareils 
radio exempts de licence. L’exploitationestautorisée aux deux conditions suivantes : 
(1) L’appareil ne doit pas produire de brouillage;   
(2) L’appareildoit accepter tout brouillage radioélectriquesubi, même si le brouillageest 
susceptible d’encompromettre le fonctionnement. 

ISED 5G Wi-Fistatement 
The user manual for LE-LAN devices shall contain instructions related to the restrictions 
mentioned in the above sections, namely that: 
i.

the device for operation in the band 5150–5250 MHz is only for indoor use to reduce

the potential for harmful interference to co-channel mobile satellite systems; 

Содержание SK700













Отзывы: