background image

5 Maintenance [specialist] 

 

 

 

2016/05 

997655910x-mub-en 

 V07

 

19 

5

 

Maintenance [specialist] 

5.1

 

Draining the solar installation 

 

1.

 

Switch off the controller and make sure that  
a restart is not possible. 

2.

 

Open the check valves in the return ball 
valves [1.2I7.2], by turning them to position 
45° (45°, see page 12).  

3.

 

Connect a heat-resistant hose to the lowest 
drain valve of the solar installation (possibly 
drain valve [9.2]). 
Make sure that the solar fluid is collected in  
a heat-resistant container.  

 

 

WARNING 

Danger of scalding due to hot solar fluid! 

The escaping solar fluid may be very hot.  

 

Place and secure the heat-resistant collecting container in such a way that 
people standing nearby are not endangered during the draining of the solar 
installation. 

 

4.

 

Open the lowest drain valve of the solar installation. 

5.

 

To accelerate the draining of the solar circuit, the vent valve possibly  
present at the highest point of the solar installation can be opened. 

6.

 

Dispose of the solar fluid observing the local regulations. 

 

 

 

5.2

 

Deinstallation 

1.

 

Drain the solar installation as described above. 

2.

 

Disconnect the pipe connections to the solar system. 

3.

 

To remove the solar station from the wall bracket,  
pull out the clip springs laterally with a screwdriver. 

4.

 

Remove the station by pulling it forward.  

Содержание SolarBloC midi 2D





























Отзывы: