manualshive.com logo in svg

PAW FC4.13, Руководство для специализированных мастеров

Поделиться
Скачать
PAW FC4.13 Скачать руководство пользователя страница 19

19

en

Maximum speed of the primary pump

Main menu / Store loading / Prim. max. speed

Adjustment channel Description

Adjustment  range / 
selection

Factory 
setting

Prim. max. speed

Maximum speed of the primary pump 1.5 … 100 %

100 %

With the parameter Prim. max. speed the maximum speed of the primary pump 
can be adjusted.

Note:
The adjustable value represents the speed of the corresponding pump.
Maximum speed (100 %) is reached at 80 to 90 % of the PWM signal duty 
cycle. The minimum value (1.5 %) is reached at 10 to 20 % of the PWM 
signal duty cycle.
The power of the PWM signal is indicated in the status menu.

Maximum speed of the secondary pump

Main menu / Store loading / Sec. max. speed

Adjustment channel Description

Adjustment  range / 
selection

Factory 
setting

Sec. max. speed

Maximum speed of the secondary pump 1.5 … 100 %

80 %

With the parameter Sec. max. speed the maximum speed of the primary pump 
can be adjusted.

Note:
The adjustable values of both channels represent the speed of the cor-
responding pump.
Maximum speed (100 %) is reached at 80 to 90 % of the PWM signal duty 
cycle. The minimum value (1.5 %) is reached at 10 to 20 % of the PWM 
signal duty cycle.
The duty cycle of the corresponding PWM signal is indicated in the status 
menu.

Minimum hot water set temperature

Main  menu / Store  loading / Set  min

Adjustment channel Description

Adjustment  range / 
selection

Factory 
setting

Set min

Minimum hot water set temperature

20 … 75 °C

20 °C

This parameter determines the minimum limitation for the adjustment of the hot 
water set temperature T-HW set.

Содержание FC4.13





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды