3.2 INTERFACE POWER OPTION JUMPERS
Both versions of the Model 2400 can be powered from the supplied
AC power source, from DC power supplied to the power supply jack or
directly from the local RS-232/V.24 (Model 2400/A) or V.35 (Model
2400/C) interface. To configure the unit to receive power from the local
interface, please refer to Sections 3.2.1 (Model 2400/A) and 3.2.2
(Model 2400/C).
3.2.1 Interface Power Option (Model 2400/A)
Two jumper straps (JP1 and JP2) are used in combination to set
the Model 2400/A to receive its power from the RS-232 interface.
Figure 6 shows the position of JP1 and JP2 on the top side of the
Model 2400/A PC board.
Figure 7 below shows the orientation of the pins on the six pin
jumper block and possible settings of jumper straps JP1 and JP2.
@@@@@@@@e?
@@@@@@@@e?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e
@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e
@@@@@@@@
@@@@@@@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
?@@
?@@
?@@
?@@
?@@
?@@
?@@@@@@@@
?@@@@@@@@
?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@
?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@
@@g
@@g
@@g
@@g
@@g
@@g
@@@@@@@@
@@@@@@@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@@@@@@@e?
@@@@@@@@e?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e
@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e
@@@@@@@@
@@@@@@@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
?@@
?@@
?@@
?@@
?@@
?@@
?@@@@@@@@
?@@@@@@@@
?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@
?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@
@@g
@@g
@@g
@@g
@@g
@@g
@@@@@@@@
@@@@@@@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
NOTE: “*” indicates Factory Default Setting
JP1: DC Power Supplied by Pin 9
The Model 2400/A may be configured to receive its operating
power from by pin 9 on the RS-232 interface. In the normal setting,
pin 9 is not used for interface power.
JP1
Position 1 & 4
Normal
(default)
Position 4 & 5
Pin 9 Used for Interface Power. In this setting
the 2400/A is powered from the DTE
interface. Power should be applied to pin 9
at +5VDC (±5%), 200mA. The AC wall-
mount transformer must not be connected
in this setting.
NOTE: The only allowable positions for Jumper JP1 are as listed
above.
JP2: DC Power Supplied by Pin 21
The Model 2400/A may be configured to receive its operating
power from by pin 21 on the RS-232 interface. In the normal setting,
pin 21 is used for its normal function.
JP2
Position 5 & 6
Pin 21 Used for Interface Power. In this setting
the 2400/A Series unit is powered from the
DTE interface. Powered should be applied to
pin 9 at +5VDC (±5%), 200mA. The AC
wall-mount transformer must not be
connected in this setting.
Position 3 & 6
Normal
(default)
NOTE: The only allowable positions for Jumper JP2 are as listed
above.
9
10
Figure 7. Possible Settings of Jumper Strap JP1 for Model 2400/A
JP1
JP2
Figure 6. Position of the DIP Switches on the 2400/A PC board
Switch S1
WARNING: The Model 2400 will be damaged and will not be
covered by warranty if any other power supply input than 5VDC
±5% is used with the Interface Power Option.
5
2
6
3
1
4
POSSIBLE SETTING COMBINATIONS FOR JP1 & JP2
JP1
JP2
Function
1 & 4
5 & 6
DC Powered by Pin 21
1 & 4
3 & 6
Normal*
4 & 5
3 & 6
DC Powered by Pin 9