background image

14

5.0  OPERATION

Once the Model 1069 is properly installed, it should operate transpar-
ently. No user settings required. This section describes reading the LED 
status monitors.

Before applying power to the Model 1069, please review section 3.4, 
“Connecting Power” on page 12 to verify that the unit is connected to the 
appropriate power source.

5.1  FRONT PANEL LED STATUS MONITORS

The Model 1069 features six front panel LEDs that monitor power, the 
Ethernet signals, the VDSL2 connection, and the remote/local setting. 
Figure 8 shows the front panel location of each LED. Table 2 on page 14 
describes the LED functions.

Figure 8. 

Model 1069 front panel

Table 2: 

Front panel LED description

LED

Status

Description

Power

Green

The device is powered on.

Off

The device is powered off.

DSL

Green

The port is connected.

Blinking Green

Data transceiving.

Off

No valid link on this port.

CPE

Green

The device is operating in CPE (Remote) mode.

Off

The device is operating in CO (Local) mode.

Ethernet

Green

The port is connected.

*

Blinking Green

*.

Once the unit connects to a power source, the Link LED will blink 
as the 1069 automatically looks for the other unit.

Data transceiving.

DSL Link

CPE (Remote) Mode

Power

Ethernet Link

Содержание OnSite 1069





















Отзывы: